Thanks, Pat.
I will probably not be able to do anything until after Field Day, but I'm
keeping these e-mails so I have a list of things to try when I am free
again.
73 from Tom Behler: KB8TYJ
----- Original Message -----
From: "Pat Byrne" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Friday, June 24, 2011 11:04 PM
Subject: Re: TS590 output power and ALC question
And too, Tom you could have proper voltage at the Astron meter but
not at the rig end of the 12 volt line. If you can sneak your DVM
across the power leads where they enter the rig you might be
surprised, perhaps happily!!
Good luck with Field Day.
Pat, K9JAUAt 08:12 PM 6/24/2011, you wrote:
> Lowell:
>
>I am using an Astron 35 power supply here, but am not sure how to safely
>take its voltage reading. I do have a sighted xyl, so will ask her to look
>at the meter on the front of the supply.
>
>I wonder if the supply is at a slightly lower voltage, which is why I'm
>only
>getting about 90 watts out into a dummy load, and a resonant antenna.
>
>Either that, or perhaps my TW1 is a little off on its readings.
>
>73 from Tom Behler: KB8TYJ
>
>----- Original Message -----
>From: "Lowell Miller" <[log in to unmask]>
>To: <[log in to unmask]>
>Sent: Friday, June 24, 2011 7:50 PM
>Subject: Re: TS590 output power and ALC question
>
>
>Hi Butch,
>I have been reading the mail here and I think you will find that you must
>have 13.8 volts to get max output.
>I have a power supply with adjustable voltage out put just for that reason.
>My 590 puts out about 105-110 according to my TW1.
>I hope that will help you.
>best 73
>Lowell W8QIY
>----- Original Message -----
>From: "Butch Bussen" <[log in to unmask]>
>To: <[log in to unmask]>
>Sent: Friday, June 24, 2011 7:42 PM
>Subject: Re: TS590 output power and ALC question
>
>
> >I just took mine down to the work bench and hooked it up to my ifr
> > service monitor which is one ver expensive piece of test equipment. I
> > show 90 watts on 160 and ten, but my voltage drops to aaround 12.2 right
> > at the power plug. I'm wondering if this rig is very picky about supply
> > voltage. I'm going to do some playing with that.
> >
> > 73
> > Butch
> > WA0VJR
> > Node 3148
> > Wallace, ks.
> >
> >
> > On Fri, 24 Jun 2011,
> > tom behler wrote:
> >
> >> Butch:
> >>
> >> I'll post to the list here, and see what they say.
> >>
> >> I am closer to the 100 watts than you are, but it is still a bit
> >> strange.
> >>
> >> There are two ways you can subscribe to the TS590 group.
> >>
> >> One is via the yahoogroups web site, and the other is via e-mail.
> >>
> >> When subscribing, give them your call, so they can verify that you are
> >> a
> >> ham, and not some sort of a spammer.
> >>
> >> If you want to try the e-mail route, which is how I think I ultimately
> >> succeeded, send an e-mail to:
> >>
> >> [log in to unmask]
> >>
> >> 73 from Tom Behler: KB8TYJ
> >>
> >>
> >> ----- Original Message -----
> >> From: "Butch Bussen" <[log in to unmask]>
> >> To: <[log in to unmask]>
> >> Sent: Friday, June 24, 2011 5:41 PM
> >> Subject: Re: TS590 output power and ALC question
> >>
> >>
> >> I had similar problems. Could you post to the 590 list and see if
> >> others are having this problem? Also, could you give me the exact name
> >> of the list and how you subscribed. I tried two tw1 meeters with
> >> similar results. I'm going to hook mine up on the bench in the
> >> basement
> >> on my ifr service monitor and see what it says. I called Universal and
> >> they say they're sending a call tag, but Kenwood wants to look at it
> >> before they replace it. Bummer!!!
> >>
> >> Keep me posted Tom, and I'll post my further test results here as well.
> >> 73
> >> Butch
> >> WA0VJR
> >> Node 3148
> >> Wallace, ks.
> >>
> >>
> >> On
> >> Fri, 24 Jun 2011, tom behler wrote:
> >>
> >>> Hi, folks.
> >>>
> >>> Well, I actually got my TS590 on the air today, and got good reports.
> >>>
> >>> Hopefully, I'll join you guys real soon on one of our nets so you can
> >>> hear
> >>> it for yourselves.
> >>>
> >>> I do have a question about output power readings, though.
> >>>
> >>> It seems like I am getting about 90 watts out of the TS590 when using
> >>> a
> >>> dummy load.
> >>>
> >>> I tried adjusting the carrier level, as I think Kevin suggested, using
> >>> the
> >>> forward power tone on the TW1, but my highest tone is at about a level
> >>> of
> >>> 70.
> >>>
> >>> One other thing I have noticed is that when I take ALC readings, the
> >>> TS590
> >>> keeps saying "A over".
> >>>
> >>> This would indicate to me that something might be out of adjustment.
> >>>
> >>> If anyone has any suggestions about settings, etc., please let me
> >>> know.
> >>>
> >>> Thanks, and 73 from Tom Behler: KB8TYJ
> >>>
> >>>
> >>
> >>
|
