Lou,
I second that, mainly because there just aren't enough PF keys to go around
unless you use all four on the mic. Furthermore, each key should have its
own momentary contact switch (most likely a button).
Steve
----- Original Message -----
From: "Louis Kim Kline" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Monday, March 03, 2008 20:26
Subject: Re: building a box for function keys
> Hi Colin.
>
> I actually use all four PF keys on my TS2000S. PF1 = Speak Frequency
> Info,
> PF2 = Speak S meter reading; PF3 = Open Squelch, and PF4 = Listen on
> transmit frequency (I forgot what Kenwood calls those last two
> functions). I like being to listen on the input of a repeater with PF4
> nearly as much as being able to listen to my S meter reading and my
> frequency info. So, I guess I'd want all four PF keys.
>
> 73, de Lou K2LKK
>
>
>
> At 01:04 AM 3/3/2008 -0700, you wrote:
>>The idea is to build a box that has control over the four buttons
>>typically
>>found at the top of an MC45 type hand mike.
>>These are the PF key, vfo, call and MR.
>>RE assignable on most radios to perform various functions.
>>If a person uses a desk mike with either the kenwood dual band mobile
>>rigs,
>>or any of the HF rigs that offer both S meter and freq read out, then the
>>operator is limited to the use of a single function key, the one on the
>>radio.
>>This means you must assign either the freq readout, or S meter read out to
>>that single PF key, not allowing for both to be simaltaniously programmed.
>>This is only if you use a desk mike, or a microphone that does not have
>>the
>>four function keys.
>>this is how these functions are performed electronically using 3 pins of
>>the
>>mike jack:
>>This is a listing for the mc45DM mikes, but I would suspect that the
>>resister values are universal for most kenwood radios.
>>This shows the pinout for an RJ45, not an 8 pin kenwood din jack like on
>>the ts2000.
>>The pinout for the ts2000 would likely be something like pin 3 and pin
>>four
>>shorter to either pin 6, or pin 8, which is PTT or chassis ground.
>>
>>
>>Resistance value
>>between pin 6 and pin 8
>>between pin 6 and pin 1
>>0 ohm
>>UP
>>DWN
>>22 kohm
>>CALL
>>MR
>>100 kohm
>>VFO
>>PF
>>
>>Personally, I very rarely use more then two function keys on my mc45DM and
>>the ts2000. I use two of the keys for S meter reading and freq readout.
>>So, for me, I would simply reassign the VFO key for freq read out, and the
>>PF key for S meter readout in the rigs menus, and then use a 100K ohm
>>resister on a two way mini momentary toggles switch, or some other sort of
>>microswitch with a two way momentary set up. Basically you short pin 8 to
>>pin 6 through a 100K resister to obtain the VFO function switch, and short
>>pin 1 to pin 6 through a 100K resister to obtain the PF keys function.
>>I suspect that pin 6 is chassis ground, but perhaps not since there is one
>>more pin for a typical 8 pin round jack settup that doesn't appear to have
>>a
>>function, which might be that of controlling the function keys.
>>
>>A small hamond box, with an 8 pin standard din jack, or perhaps with the
>>RJ45, one for input, one for out put, would fit the bill just nicely.
>>Now, how to implement a DTMF pad hmmmm.
>>While I'm at it, I might as well put in an XLR jack for a studio
>>microphone, a PTT switch, and a jack for a foot switch.
>>But of course, that would mean a relay, and an audio isolation
>>transformer.
>>
>>any thoughts are welcome on what I have outlined here.
>>
>>73
>>Colin, V A6BKX
>>
>>
>>
>>
>>--
>>No virus found in this incoming message.
>>Checked by AVG Free Edition.
>>Version: 7.5.516 / Virus Database: 269.21.4/1309 - Release Date: 3/3/2008
>>6:50 PM
>
> Louis Kim Kline
> A.R.S. K2LKK
> Home e-mail: [log in to unmask]
> Work e-mail: [log in to unmask]
> Work Telephone: (585) 697-5740
>
>
>
>
|