I’m currently at my actual house, not at school. trying to get onto I think it’s K1SMH located in attleboro.
> On Dec 23, 2014, at 4:31 PM, John Miller <[log in to unmask]> wrote:
>
> Are you not transmitting the right tone for the repeater? Are you home? If
> so which repeater is it? I may be able to help, were not far from each other
> and the closest repeaters to you at home I'm very familiar with.
> John N1UMJ
> ----- Original Message -----
> From: "Ashley Bernard" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Tuesday, December 23, 2014 4:14 PM
> Subject: Re: puxing 973 ht not receiving audio
>
>
>> The radios do hear each other. The problem is that when I let go of the =
>> PTT button on the Puxing I get no courtesy tone or sound of the repeater =
>> dropping, when in reality the transmission went through perfectly fine =
>> as I heard it 100 percent on my other radio.
>> 73.
>> Ashley KC1CPS
>>> On Dec 23, 2014, at 4:11 PM, Colin McDonald <[log in to unmask]> =
>> wrote:
>>> =20
>>> OK.
>>> SO can you hear your puxing transmitting, with your kenwood, on the =
>> repeater=20
>>> input?
>>> And vice versa? can you hear the kenwood transmitting on the repeater =
>> input=20
>>> with the puxing?
>>> Meaning only on the input frequency, not through the repeater.
>>> Perhaps do this test on a simplex frequency to find out if the radios =
>> hear=20
>>> each other.
>>> You can trouble shoot these problems by eliminating one thing after =
>> another.
>>> Any technical problem solving/trouble shooting must be done in a =
>> liniar=20
>>> fashion to remove each potential issue one at a time until you find =
>> the=20
>>> problem.
>>> =20
>>> 73
>>> Colin, V A6BKX
>>> -----Original Message-----=20
>>> From: Ashley Bernard
>>> Sent: Tuesday, December 23, 2014 2:02 PM
>>> To: [log in to unmask]
>>> Subject: Re: puxing 973 ht not receiving audio
>>> =20
>>> yeah. it=3DE2=3D80=3D99s my radio. My kenwood is operating on the same =
>> =3D
>>> repeater just fine.
>>> =20
>>>> On Dec 23, 2014, at 4:01 PM, Colin McDonald <[log in to unmask]> =
>> =3D
>>> wrote:
>>>> =3D20
>>>> Ashley, is this on all repeater frequencies? or just one? could the =
>> =3D
>>> machine=3D20
>>>> be down or temperarily off the air for maintenance?
>>>> It does happen.
>>>> Do you have another radio to test your receive and transmit?
>>>> =3D20
>>>> 73
>>>> Colin, V A6BKX
>>>> =3D20
>>>> -----Original Message-----=3D20
>>>> From: Ashley Bernard
>>>> Sent: Tuesday, December 23, 2014 1:36 PM
>>>> To: [log in to unmask]
>>>> Subject: Re: puxing 973 ht not receiving audio
>>>> =3D20
>>>> now I=3D3DE2=3D3D80=3D3D99ve reset, and am back to my original =
>> problem of =3D
>>> not being =3D3D
>>>> able to hear anything once I transmit. I=3D3DE2=3D3D80=3D3D99m =
>> definitely =3D3D
>>>> transmitting now, just not being notified. I=3D3DE2=3D3D80=3D3D99ve =
>> tried =3D
>>> turning =3D3D
>>>> off what you instructed to turn off but still haven=3D3DE2=3D3D80=3D3D9=
>> 9t =3D
>>> solved the =3D3D
>>>> issue yet.
>>>> =3D20
>>>>> On Dec 23, 2014, at 3:28 PM, Buddy Brannan <[log in to unmask]> =3D
>>> wrote:
>>>>> =3D3D20
>>>>> That sounds like you maybe are transmitting but changed your offset =
>> =3D
>>> =3D3D3D
>>>>> amount or direction.
>>>>> =3D3D20
>>>>> If you want to do a full reset, hold down menu while turning the =3D
>>> radio =3D3D
>>>> =3D3D3D
>>>>> on. Wait a second after the beep, and then let go. Press confirm =3D3D=
>>
>>>> twice. =3D3D3D
>>>>> That should reset everything but keep your memory channels =3D
>>> intact.=3D3D3D20
>>>>> =3D3D20
>>>>> =3D3D3DE2=3D3D3D80=3D3D3D94=3D3D3D20
>>>>> Buddy Brannan, KB5ELV - Erie, PA
>>>>> Phone: 814-860-3194=3D3D3D20
>>>>> Mobile: 814-431-0962
>>>>> Email: [log in to unmask]
>>>>> =3D3D20
>>>>> =3D3D20
>>>>> =3D3D20
>>>>>> On Dec 23, 2014, at 3:25 PM, Ashley Bernard <[log in to unmask]> =3D3D=
>>
>>>> wrote:
>>>>>> =3D3D3D20
>>>>>> so I did that, and now I don=3D3D3D3DE2=3D3D3D3D80=3D3D3D3D99t =
>> appear to =3D
>>> be able =3D3D
>>>> to =3D3D3D
>>>>> transmit at =3D3D3D3D
>>>>>> all. not sure what=3D3D3D3DE2=3D3D3D3D80=3D3D3D3D99s going on.
>>>>>> Thanks.
>>>>>> Ashley
>>>>>> =3D3D3D20
>>>>>>> On Dec 23, 2014, at 2:37 PM, Buddy Brannan <[log in to unmask]> =
>> =3D3D3D=3D
>>> =20
>>>>> wrote:
>>>>>>> =3D3D3D3D20
>>>>>>> Hi,
>>>>>>> =3D3D3D3D20
>>>>>>> Likely you=3D3D3D3D3DE2=3D3D3D3D3D80=3D3D3D3D3D99ve turned on =
>> CTCSS =3D
>>> squelch. Try =3D3D
>>>> this:
>>>>>>> =3D3D3D3D20
>>>>>>> 1) Press menu.
>>>>>>> =3D3D3D3D20
>>>>>>> 2) Press the # key.
>>>>>>> =3D3D3D3D20
>>>>>>> 3) Press Enter (next to menu).
>>>>>>> =3D3D3D3D20
>>>>>>> 4) Press * twice. Then press the number 1. If you get a high =3D
>>> pitched =3D3D
>>>> =3D3D3D
>>>>> =3D3D3D3D3D=3D3D3D3D
>>>>>> =3D3D3D20
>>>>>>> tone with an error prompt, tones are all turned off. If you =
>> =3D3D3D3D
>>>>>> don=3D3D3D3D3DE2=3D3D3D3D3D80=3D3D3D3D3D99t,=3D3D3D3D3D
>>>>>>> press * until you do.
>>>>>>> =3D3D3D3D20
>>>>>>> 5) Press enter again.
>>>>>>> =3D3D3D3D20
>>>>>>> 6) Rotate the selector knob once clockwise and repeat above steps =
>> =3D
>>> to =3D3D
>>>> =3D3D3D
>>>>> =3D3D3D3D
>>>>>> be =3D3D3D3D3D
>>>>>>> sure receive CTCSS is off.=3D3D3D3D3D20
>>>>>>> =3D3D3D3D20
>>>>>>> =3D3D3D3D20
>>>>>>> =3D3D3D3D3DE2=3D3D3D3D3D80=3D3D3D3D3D94=3D3D3D3D3D20
>>>>>>> Buddy Brannan, KB5ELV - Erie, PA
>>>>>>> Phone: 814-860-3194=3D3D3D3D3D20
>>>>>>> Mobile: 814-431-0962
>>>>>>> Email: [log in to unmask]
>>>>>>> =3D3D3D3D20
>>>>>>> =3D3D3D3D20
>>>>>>> =3D3D3D3D20
>>>>>>>> On Dec 23, 2014, at 2:26 PM, Ashley Bernard <[log in to unmask]> =3D=
>>
>>> =3D3D3D3D=3D3D
>>>> =3D20
>>>>>> wrote:
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> Hi list,
>>>>>>>> In my exploration with repeaters and radio operation, =3D3D3D3D3D
>>>>>>> I=3D3D3D3D3D3DE2=3D3D3D3D3D3D80=3D3D3D3D3D3D99ve=3D3D3D3D3D3D
>>>>>>>> managed to mess up my audio on my puxing ht. The speech output =
>> =3D3D
>>>> works =3D3D3D
>>>>> =3D3D3D3D
>>>>>> =3D3D3D3D3D3D=3D3D3D3D3D
>>>>>>> =3D3D3D3D20
>>>>>>>> fine, and when I hit the PTT button I can tell my transmission =3D
>>> went =3D3D
>>>> =3D3D3D
>>>>> =3D3D3D3D
>>>>>> =3D3D3D3D3D3D
>>>>>>>> through by listening from another radio, but =3D3D
>>>> I=3D3D3D3D3D3DE2=3D3D3D3D3D3D80=3D3D3D3D3D3=3D3D3D
>>>>> D99m =3D3D3D3D
>>>>>> =3D3D3D3D3D
>>>>>>> receiving no =3D3D3D3D3D3D
>>>>>>>> audio on the puxing side. If anyone knows a reset function or =
>> =3D3D3D
>>>>> another =3D3D3D3D
>>>>>> =3D3D3D3D3D
>>>>>>> =3D3D3D3D3D3D
>>>>>>>> way to fix this problem it would be much appreciated.
>>>>>>>> Ashley (KC1CPS)=3D3D3D3D3D3D=3D20=20
|
