Nope the pl out is the same as in, I monitor that machine usually and always
run tone squelch.
----- Original Message -----
From: "Butch Bussen" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Tuesday, December 23, 2014 8:41 PM
Subject: Re: puxing 973 ht not receiving audio
>I can't make much out of all this because of all those equals signs, but
> sounds to me like receive is set to pl, so either the repeater isn't
> sending out a pl tone or it is different than the one set. Try setting
> receive to open squelch, you can calso tap the monitor button to open
> squelch and see if you hear the repeater.
> 73
> Butch
> WA0VJR
> Node 3148
> Wallace, ks.
>
>
> On Tue, 23 Dec 2014, John Miller
> wrote:
>
>> Are you not transmitting the right tone for the repeater? Are you home?
>> If
>> so which repeater is it? I may be able to help, were not far from each
>> other
>> and the closest repeaters to you at home I'm very familiar with.
>> John N1UMJ
>> ----- Original Message -----
>> From: "Ashley Bernard" <[log in to unmask]>
>> To: <[log in to unmask]>
>> Sent: Tuesday, December 23, 2014 4:14 PM
>> Subject: Re: puxing 973 ht not receiving audio
>>
>>
>>> The radios do hear each other. The problem is that when I let go of the
>>> =
>>> PTT button on the Puxing I get no courtesy tone or sound of the repeater
>>> =
>>> dropping, when in reality the transmission went through perfectly fine =
>>> as I heard it 100 percent on my other radio.
>>> 73.
>>> Ashley KC1CPS
>>>> On Dec 23, 2014, at 4:11 PM, Colin McDonald <[log in to unmask]> =
>>> wrote:
>>>> =20
>>>> OK.
>>>> SO can you hear your puxing transmitting, with your kenwood, on the =
>>> repeater=20
>>>> input?
>>>> And vice versa? can you hear the kenwood transmitting on the repeater =
>>> input=20
>>>> with the puxing?
>>>> Meaning only on the input frequency, not through the repeater.
>>>> Perhaps do this test on a simplex frequency to find out if the radios =
>>> hear=20
>>>> each other.
>>>> You can trouble shoot these problems by eliminating one thing after =
>>> another.
>>>> Any technical problem solving/trouble shooting must be done in a =
>>> liniar=20
>>>> fashion to remove each potential issue one at a time until you find =
>>> the=20
>>>> problem.
>>>> =20
>>>> 73
>>>> Colin, V A6BKX
>>>> -----Original Message-----=20
>>>> From: Ashley Bernard
>>>> Sent: Tuesday, December 23, 2014 2:02 PM
>>>> To: [log in to unmask]
>>>> Subject: Re: puxing 973 ht not receiving audio
>>>> =20
>>>> yeah. it=3DE2=3D80=3D99s my radio. My kenwood is operating on the same
>>>> =
>>> =3D
>>>> repeater just fine.
>>>> =20
>>>>> On Dec 23, 2014, at 4:01 PM, Colin McDonald <[log in to unmask]> =
>>> =3D
>>>> wrote:
>>>>> =3D20
>>>>> Ashley, is this on all repeater frequencies? or just one? could the =
>>> =3D
>>>> machine=3D20
>>>>> be down or temperarily off the air for maintenance?
>>>>> It does happen.
>>>>> Do you have another radio to test your receive and transmit?
>>>>> =3D20
>>>>> 73
>>>>> Colin, V A6BKX
>>>>> =3D20
>>>>> -----Original Message-----=3D20
>>>>> From: Ashley Bernard
>>>>> Sent: Tuesday, December 23, 2014 1:36 PM
>>>>> To: [log in to unmask]
>>>>> Subject: Re: puxing 973 ht not receiving audio
>>>>> =3D20
>>>>> now I=3D3DE2=3D3D80=3D3D99ve reset, and am back to my original =
>>> problem of =3D
>>>> not being =3D3D
>>>>> able to hear anything once I transmit. I=3D3DE2=3D3D80=3D3D99m =
>>> definitely =3D3D
>>>>> transmitting now, just not being notified. I=3D3DE2=3D3D80=3D3D99ve =
>>> tried =3D
>>>> turning =3D3D
>>>>> off what you instructed to turn off but still
>>>>> haven=3D3DE2=3D3D80=3D3D9=
>>> 9t =3D
>>>> solved the =3D3D
>>>>> issue yet.
>>>>> =3D20
>>>>>> On Dec 23, 2014, at 3:28 PM, Buddy Brannan <[log in to unmask]> =3D
>>>> wrote:
>>>>>> =3D3D20
>>>>>> That sounds like you maybe are transmitting but changed your offset =
>>> =3D
>>>> =3D3D3D
>>>>>> amount or direction.
>>>>>> =3D3D20
>>>>>> If you want to do a full reset, hold down menu while turning the =3D
>>>> radio =3D3D
>>>>> =3D3D3D
>>>>>> on. Wait a second after the beep, and then let go. Press confirm
>>>>>> =3D3D=
>>>
>>>>> twice. =3D3D3D
>>>>>> That should reset everything but keep your memory channels =3D
>>>> intact.=3D3D3D20
>>>>>> =3D3D20
>>>>>> =3D3D3DE2=3D3D3D80=3D3D3D94=3D3D3D20
>>>>>> Buddy Brannan, KB5ELV - Erie, PA
>>>>>> Phone: 814-860-3194=3D3D3D20
>>>>>> Mobile: 814-431-0962
>>>>>> Email: [log in to unmask]
>>>>>> =3D3D20
>>>>>> =3D3D20
>>>>>> =3D3D20
>>>>>>> On Dec 23, 2014, at 3:25 PM, Ashley Bernard <[log in to unmask]>
>>>>>>> =3D3D=
>>>
>>>>> wrote:
>>>>>>> =3D3D3D20
>>>>>>> so I did that, and now I don=3D3D3D3DE2=3D3D3D3D80=3D3D3D3D99t =
>>> appear to =3D
>>>> be able =3D3D
>>>>> to =3D3D3D
>>>>>> transmit at =3D3D3D3D
>>>>>>> all. not sure what=3D3D3D3DE2=3D3D3D3D80=3D3D3D3D99s going on.
>>>>>>> Thanks.
>>>>>>> Ashley
>>>>>>> =3D3D3D20
>>>>>>>> On Dec 23, 2014, at 2:37 PM, Buddy Brannan <[log in to unmask]> =
>>> =3D3D3D=3D
>>>> =20
>>>>>> wrote:
>>>>>>>> =3D3D3D3D20
>>>>>>>> Hi,
>>>>>>>> =3D3D3D3D20
>>>>>>>> Likely you=3D3D3D3D3DE2=3D3D3D3D3D80=3D3D3D3D3D99ve turned on =
>>> CTCSS =3D
>>>> squelch. Try =3D3D
>>>>> this:
>>>>>>>> =3D3D3D3D20
>>>>>>>> 1) Press menu.
>>>>>>>> =3D3D3D3D20
>>>>>>>> 2) Press the # key.
>>>>>>>> =3D3D3D3D20
>>>>>>>> 3) Press Enter (next to menu).
>>>>>>>> =3D3D3D3D20
>>>>>>>> 4) Press * twice. Then press the number 1. If you get a high =3D
>>>> pitched =3D3D
>>>>> =3D3D3D
>>>>>> =3D3D3D3D3D=3D3D3D3D
>>>>>>> =3D3D3D20
>>>>>>>> tone with an error prompt, tones are all turned off. If you =
>>> =3D3D3D3D
>>>>>>> don=3D3D3D3D3DE2=3D3D3D3D3D80=3D3D3D3D3D99t,=3D3D3D3D3D
>>>>>>>> press * until you do.
>>>>>>>> =3D3D3D3D20
>>>>>>>> 5) Press enter again.
>>>>>>>> =3D3D3D3D20
>>>>>>>> 6) Rotate the selector knob once clockwise and repeat above steps =
>>> =3D
>>>> to =3D3D
>>>>> =3D3D3D
>>>>>> =3D3D3D3D
>>>>>>> be =3D3D3D3D3D
>>>>>>>> sure receive CTCSS is off.=3D3D3D3D3D20
>>>>>>>> =3D3D3D3D20
>>>>>>>> =3D3D3D3D20
>>>>>>>> =3D3D3D3D3DE2=3D3D3D3D3D80=3D3D3D3D3D94=3D3D3D3D3D20
>>>>>>>> Buddy Brannan, KB5ELV - Erie, PA
>>>>>>>> Phone: 814-860-3194=3D3D3D3D3D20
>>>>>>>> Mobile: 814-431-0962
>>>>>>>> Email: [log in to unmask]
>>>>>>>> =3D3D3D3D20
>>>>>>>> =3D3D3D3D20
>>>>>>>> =3D3D3D3D20
>>>>>>>>> On Dec 23, 2014, at 2:26 PM, Ashley Bernard <[log in to unmask]>
>>>>>>>>> =3D=
>>>
>>>> =3D3D3D3D=3D3D
>>>>> =3D20
>>>>>>> wrote:
>>>>>>>>> =3D3D3D3D3D20
>>>>>>>>> Hi list,
>>>>>>>>> In my exploration with repeaters and radio operation, =3D3D3D3D3D
>>>>>>>> I=3D3D3D3D3D3DE2=3D3D3D3D3D3D80=3D3D3D3D3D3D99ve=3D3D3D3D3D3D
>>>>>>>>> managed to mess up my audio on my puxing ht. The speech output =
>>> =3D3D
>>>>> works =3D3D3D
>>>>>> =3D3D3D3D
>>>>>>> =3D3D3D3D3D3D=3D3D3D3D3D
>>>>>>>> =3D3D3D3D20
>>>>>>>>> fine, and when I hit the PTT button I can tell my transmission =3D
>>>> went =3D3D
>>>>> =3D3D3D
>>>>>> =3D3D3D3D
>>>>>>> =3D3D3D3D3D3D
>>>>>>>>> through by listening from another radio, but =3D3D
>>>>> I=3D3D3D3D3D3DE2=3D3D3D3D3D3D80=3D3D3D3D3D3=3D3D3D
>>>>>> D99m =3D3D3D3D
>>>>>>> =3D3D3D3D3D
>>>>>>>> receiving no =3D3D3D3D3D3D
>>>>>>>>> audio on the puxing side. If anyone knows a reset function or =
>>> =3D3D3D
>>>>>> another =3D3D3D3D
>>>>>>> =3D3D3D3D3D
>>>>>>>> =3D3D3D3D3D3D
>>>>>>>>> way to fix this problem it would be much appreciated.
>>>>>>>>> Ashley (KC1CPS)=3D3D3D3D3D3D=3D20=20
>>
>>
|
