Sounds like you have PL decode turned on, and the decode is for a different
PL than the repeater transmits.
-----Original Message-----
From: For blind ham radio operators [mailto:[log in to unmask]]
On Behalf Of Ashley Bernard
Sent: Tuesday, December 23, 2014 3:15 PM
To: [log in to unmask]
Subject: Re: puxing 973 ht not receiving audio
The radios do hear each other. The problem is that when I let go of the =
PTT button on the Puxing I get no courtesy tone or sound of the repeater =
dropping, when in reality the transmission went through perfectly fine =
as I heard it 100 percent on my other radio.
73.
Ashley KC1CPS
> On Dec 23, 2014, at 4:11 PM, Colin McDonald <[log in to unmask]> =
wrote:
>=20
> OK.
> SO can you hear your puxing transmitting, with your kenwood, on the =
repeater=20
> input?
> And vice versa? can you hear the kenwood transmitting on the repeater =
input=20
> with the puxing?
> Meaning only on the input frequency, not through the repeater.
> Perhaps do this test on a simplex frequency to find out if the radios =
hear=20
> each other.
> You can trouble shoot these problems by eliminating one thing after =
another.
> Any technical problem solving/trouble shooting must be done in a =
liniar=20
> fashion to remove each potential issue one at a time until you find =
the=20
> problem.
>=20
> 73
> Colin, V A6BKX
> -----Original Message-----=20
> From: Ashley Bernard
> Sent: Tuesday, December 23, 2014 2:02 PM
> To: [log in to unmask]
> Subject: Re: puxing 973 ht not receiving audio
>=20
> yeah. it=3DE2=3D80=3D99s my radio. My kenwood is operating on the same =
=3D
> repeater just fine.
>=20
>> On Dec 23, 2014, at 4:01 PM, Colin McDonald <[log in to unmask]> =
=3D
> wrote:
>> =3D20
>> Ashley, is this on all repeater frequencies? or just one? could the =
=3D
> machine=3D20
>> be down or temperarily off the air for maintenance?
>> It does happen.
>> Do you have another radio to test your receive and transmit?
>> =3D20
>> 73
>> Colin, V A6BKX
>> =3D20
>> -----Original Message-----=3D20
>> From: Ashley Bernard
>> Sent: Tuesday, December 23, 2014 1:36 PM
>> To: [log in to unmask]
>> Subject: Re: puxing 973 ht not receiving audio
>> =3D20
>> now I=3D3DE2=3D3D80=3D3D99ve reset, and am back to my original =
problem of =3D
> not being =3D3D
>> able to hear anything once I transmit. I=3D3DE2=3D3D80=3D3D99m =
definitely =3D3D
>> transmitting now, just not being notified. I=3D3DE2=3D3D80=3D3D99ve =
tried =3D
> turning =3D3D
>> off what you instructed to turn off but still haven=3D3DE2=3D3D80=3D3D9=
9t =3D
> solved the =3D3D
>> issue yet.
>> =3D20
>>> On Dec 23, 2014, at 3:28 PM, Buddy Brannan <[log in to unmask]> =3D
> wrote:
>>> =3D3D20
>>> That sounds like you maybe are transmitting but changed your offset =
=3D
> =3D3D3D
>>> amount or direction.
>>> =3D3D20
>>> If you want to do a full reset, hold down menu while turning the =3D
> radio =3D3D
>> =3D3D3D
>>> on. Wait a second after the beep, and then let go. Press confirm =3D3D=
>> twice. =3D3D3D
>>> That should reset everything but keep your memory channels =3D
> intact.=3D3D3D20
>>> =3D3D20
>>> =3D3D3DE2=3D3D3D80=3D3D3D94=3D3D3D20
>>> Buddy Brannan, KB5ELV - Erie, PA
>>> Phone: 814-860-3194=3D3D3D20
>>> Mobile: 814-431-0962
>>> Email: [log in to unmask]
>>> =3D3D20
>>> =3D3D20
>>> =3D3D20
>>>> On Dec 23, 2014, at 3:25 PM, Ashley Bernard <[log in to unmask]> =3D3D=
>> wrote:
>>>> =3D3D3D20
>>>> so I did that, and now I don=3D3D3D3DE2=3D3D3D3D80=3D3D3D3D99t =
appear to =3D
> be able =3D3D
>> to =3D3D3D
>>> transmit at =3D3D3D3D
>>>> all. not sure what=3D3D3D3DE2=3D3D3D3D80=3D3D3D3D99s going on.
>>>> Thanks.
>>>> Ashley
>>>> =3D3D3D20
>>>>> On Dec 23, 2014, at 2:37 PM, Buddy Brannan <[log in to unmask]> =
=3D3D3D=3D
>=20
>>> wrote:
>>>>> =3D3D3D3D20
>>>>> Hi,
>>>>> =3D3D3D3D20
>>>>> Likely you=3D3D3D3D3DE2=3D3D3D3D3D80=3D3D3D3D3D99ve turned on =
CTCSS =3D
> squelch. Try =3D3D
>> this:
>>>>> =3D3D3D3D20
>>>>> 1) Press menu.
>>>>> =3D3D3D3D20
>>>>> 2) Press the # key.
>>>>> =3D3D3D3D20
>>>>> 3) Press Enter (next to menu).
>>>>> =3D3D3D3D20
>>>>> 4) Press * twice. Then press the number 1. If you get a high =3D
> pitched =3D3D
>> =3D3D3D
>>> =3D3D3D3D3D=3D3D3D3D
>>>> =3D3D3D20
>>>>> tone with an error prompt, tones are all turned off. If you =
=3D3D3D3D
>>>> don=3D3D3D3D3DE2=3D3D3D3D3D80=3D3D3D3D3D99t,=3D3D3D3D3D
>>>>> press * until you do.
>>>>> =3D3D3D3D20
>>>>> 5) Press enter again.
>>>>> =3D3D3D3D20
>>>>> 6) Rotate the selector knob once clockwise and repeat above steps =
=3D
> to =3D3D
>> =3D3D3D
>>> =3D3D3D3D
>>>> be =3D3D3D3D3D
>>>>> sure receive CTCSS is off.=3D3D3D3D3D20
>>>>> =3D3D3D3D20
>>>>> =3D3D3D3D20
>>>>> =3D3D3D3D3DE2=3D3D3D3D3D80=3D3D3D3D3D94=3D3D3D3D3D20
>>>>> Buddy Brannan, KB5ELV - Erie, PA
>>>>> Phone: 814-860-3194=3D3D3D3D3D20
>>>>> Mobile: 814-431-0962
>>>>> Email: [log in to unmask]
>>>>> =3D3D3D3D20
>>>>> =3D3D3D3D20
>>>>> =3D3D3D3D20
>>>>>> On Dec 23, 2014, at 2:26 PM, Ashley Bernard <[log in to unmask]> =3D=
> =3D3D3D3D=3D3D
>> =3D20
>>>> wrote:
>>>>>> =3D3D3D3D3D20
>>>>>> Hi list,
>>>>>> In my exploration with repeaters and radio operation, =3D3D3D3D3D
>>>>> I=3D3D3D3D3D3DE2=3D3D3D3D3D3D80=3D3D3D3D3D3D99ve=3D3D3D3D3D3D
>>>>>> managed to mess up my audio on my puxing ht. The speech output =
=3D3D
>> works =3D3D3D
>>> =3D3D3D3D
>>>> =3D3D3D3D3D3D=3D3D3D3D3D
>>>>> =3D3D3D3D20
>>>>>> fine, and when I hit the PTT button I can tell my transmission =3D
> went =3D3D
>> =3D3D3D
>>> =3D3D3D3D
>>>> =3D3D3D3D3D3D
>>>>>> through by listening from another radio, but =3D3D
>> I=3D3D3D3D3D3DE2=3D3D3D3D3D3D80=3D3D3D3D3D3=3D3D3D
>>> D99m =3D3D3D3D
>>>> =3D3D3D3D3D
>>>>> receiving no =3D3D3D3D3D3D
>>>>>> audio on the puxing side. If anyone knows a reset function or =
=3D3D3D
>>> another =3D3D3D3D
>>>> =3D3D3D3D3D
>>>>> =3D3D3D3D3D3D
>>>>>> way to fix this problem it would be much appreciated.
>>>>>> Ashley (KC1CPS)=3D3D3D3D3D3D=3D20=20
|
