Richard
1. Data rate or baud rate must be set on both ends 9600 is fine
2. Yes that 7 pin cabble you need amp ptt from the 7 pin to the center pin
of the rca amp ptt 998 in / out loop
Also you need ground
then you need the second rca cable from the 998 amp / ptt loop out to the
ameritron ptt input
Ameritron sells this cable ready to go
Thanks
73 Neil Sablatzky K8IT
Allstar Node 41838 KITLINK
Allstar Node 42087 KITLINK HUB
IRLP Node exp0068
Echolink K8IT-L
WIRES-X K8IT 11479 Room 21479
--------------------------------------------------
From: "Richard B. McDonald" <[log in to unmask]>
Sent: Monday, January 18, 2016 11:30 AM
To: <[log in to unmask]>
Subject: Re: Ameritron ALS-1306 Not Going into Bypass Mode During Tuning
> Hi Neil!
>
> OK, please let me clarify two things. First, when you say that the data
> rate (baud rate) must be set correctly "at both ends" you mean between the
> TS-2000 and the 998, right? Presently, the TS-2000's baud rate is set at
> 9600.
>
> Second, you say that the data (i.e., interface) cable between the TS-2000
> and the 998 is not enough; and that there must also be n RCA cable from
> the
> TS-2000 to the 998, and another from the 998 to the amp PTT. For the
> TS-2000, there is no RCA connecter for connection to an external amp.
> There
> is, however, a "REMOTE connector - Mates with a 7-pin male DIN connector
> for
> connecting an HF linear amplifier" (from the TS-2000's manual page 13).
> So,
> do you mean that this should connect to the 998; obviously with an RCA
> plug
> at the 998's end?
>
> 73,
> Richard KK6MRH
>
> -----Original Message-----
> From: For blind ham radio operators [mailto:[log in to unmask]]
> On Behalf Of Neil k8it
> Sent: Saturday, January 16, 2016 2:31 PM
> To: [log in to unmask]
> Subject: Re: Ameritron ALS-1306 Not Going into Bypass Mode During Tuning
>
> I do not have a TS2000 but I have a TS480SAT You must have the data rate
> set
> correct on both ends and a kenwood mode selected on the 998 Also the
> ts2000
> side must be in external amp mode Also you MUST have the second cable rca
> plug from the ts2000 to the 998 and then from the 998 to the amp ptt the
> data cable between the ts2000 and the 998 is NOT enough
>
> Thanks
> 73 Neil Sablatzky K8IT
> Allstar Node 41838 KITLINK
> Allstar Node 42087 KITLINK HUB
> IRLP Node exp0068
> Echolink K8IT-L
> WIRES-X K8IT 11479 Room 21479
>
> --------------------------------------------------
> From: "Richard B. McDonald" <[log in to unmask]>
> Sent: Saturday, January 16, 2016 11:14 AM
> To: <[log in to unmask]>
> Subject: Re: Ameritron ALS-1306 Not Going into Bypass Mode During Tuning
>
>> Hi Neil!
>>
>> Thanks *so* much for your below! This is really helpful. Please let
>> me ask you to tell me exactly 1) what the three menu settings are for
>> the TS-2000 and 2) what the two settings are for the 998. I may not
>> have these correct.
>>
>>
>> 73,
>> Richard KK6MRH
>>
>> -----Original Message-----
>> From: For blind ham radio operators
>> [mailto:[log in to unmask]]
>> On Behalf Of Neil k8it
>> Sent: Friday, January 15, 2016 4:53 PM
>> To: [log in to unmask]
>> Subject: Re: Ameritron ALS-1306 Not Going into Bypass Mode During
>> Tuning
>>
>> Make sure that the ptt output of the ts-2000 goes to the mfj-998 amp
>> input jack then the mfj-998 amp output jack goes to the als-1306 ptt
>> input this is the only configuration that will work
>>
>> Also make sure that both the 998 and ts2000 are enabled for external
>> tuner control with a kenwood radio, and both are in external amp
>> control mode
>>
>> This is three menu settings in the ts2000 and two in the 998 tuner
>>
>>
>> to troubleshoot
>> put a wattmeter on the output of the ts2000 and ensure it drops the
>> output power to 10 watts while tune button is pressed
>>
>> if that works verify that the tuner tunes the antenna before power is
>> restored to 100watts do all this with amp turned off
>>
>> then reset ts2000 output power to 30 watts and verify amp gets keyed
>> only in operate mode not standby mode
>>
>>
>> Thanks
>> 73 Neil Sablatzky K8IT
>> Allstar Node 41838 KITLINK
>> Allstar Node 42087 KITLINK HUB
>> IRLP Node exp0068
>> Echolink K8IT-L
>> WIRES-X K8IT 11479 Room 21479
>>
>> --------------------------------------------------
>> From: "Richard B. McDonald" <[log in to unmask]>
>> Sent: Friday, January 15, 2016 6:46 PM
>> To: <[log in to unmask]>
>> Subject: Ameritron ALS-1306 Not Going into Bypass Mode During Tuning
>>
>>> Hi!
>>>
>>>
>>>
>>> With my Kenwood TS-2000, I use both an Ameritron ALS-1306 amp and an
>>> MFJ-998
>>> antenna tuner. Both the 1306 and the 998 are connected to the TS-2000
>>> with
>>> their respective interface cables. I also have the 998's "Amp Enable
>>> In/OUT" RCA cables connected to the 1306.
>>>
>>>
>>>
>>> However, when I press the "Tune" (AT) button on the TS-2000, the 1306
>>> does
>>> not go into bypass mode during the tuning process. I cannot figure out
>>> why
>>> this is happening : ( I would appreciate any insights anyone has on
>>> this.
>>>
>>>
>>>
>>> 73,
>>>
>>> Richard KK6MRH
>>>
>>
>
|
