now I’ve reset, and am back to my original problem of not being able to hear anything once I transmit. I’m definitely transmitting now, just not being notified. I’ve tried turning off what you instructed to turn off but still haven’t solved the issue yet.

> On Dec 23, 2014, at 3:28 PM, Buddy Brannan <[log in to unmask]> wrote:
> 
> That sounds like you maybe are transmitting but changed your offset =
> amount or direction.
> 
> If you want to do a full reset, hold down menu while turning the radio =
> on. Wait a second after the beep, and then let go. Press confirm twice. =
> That should reset everything but keep your memory channels intact.=20
> 
> =E2=80=94=20
> Buddy Brannan, KB5ELV - Erie, PA
> Phone: 814-860-3194=20
> Mobile: 814-431-0962
> Email: [log in to unmask]
> 
> 
> 
>> On Dec 23, 2014, at 3:25 PM, Ashley Bernard <[log in to unmask]> wrote:
>> =20
>> so I did that, and now I don=3DE2=3D80=3D99t appear to be able to =
> transmit at =3D
>> all. not sure what=3DE2=3D80=3D99s going on.
>> Thanks.
>> Ashley
>> =20
>>> On Dec 23, 2014, at 2:37 PM, Buddy Brannan <[log in to unmask]> =
> wrote:
>>> =3D20
>>> Hi,
>>> =3D20
>>> Likely you=3D3DE2=3D3D80=3D3D99ve turned on CTCSS squelch. Try this:
>>> =3D20
>>> 1) Press menu.
>>> =3D20
>>> 2) Press the # key.
>>> =3D20
>>> 3) Press Enter (next to menu).
>>> =3D20
>>> 4) Press * twice. Then press the number 1. If you get a high pitched =
> =3D3D=3D
>> =20
>>> tone with an error prompt, tones are all turned off. If you =3D
>> don=3D3DE2=3D3D80=3D3D99t,=3D3D
>>> press * until you do.
>>> =3D20
>>> 5) Press enter again.
>>> =3D20
>>> 6) Rotate the selector knob once clockwise and repeat above steps to =
> =3D
>> be =3D3D
>>> sure receive CTCSS is off.=3D3D20
>>> =3D20
>>> =3D20
>>> =3D3DE2=3D3D80=3D3D94=3D3D20
>>> Buddy Brannan, KB5ELV - Erie, PA
>>> Phone: 814-860-3194=3D3D20
>>> Mobile: 814-431-0962
>>> Email: [log in to unmask]
>>> =3D20
>>> =3D20
>>> =3D20
>>>> On Dec 23, 2014, at 2:26 PM, Ashley Bernard <[log in to unmask]> =3D
>> wrote:
>>>> =3D3D20
>>>> Hi list,
>>>> 	In my exploration with repeaters and radio operation, =3D3D
>>> I=3D3D3DE2=3D3D3D80=3D3D3D99ve=3D3D3D
>>>> managed to mess up my audio on my puxing ht. The speech output works =
> =3D
>> =3D3D3D=3D3D
>>> =3D20
>>>> fine, and when I hit the PTT button I can tell my transmission went =
> =3D
>> =3D3D3D
>>>> through by listening from another radio, but I=3D3D3DE2=3D3D3D80=3D3D3=
> D99m =3D
>> =3D3D
>>> receiving no =3D3D3D
>>>> audio on the puxing side. If anyone knows a reset function or =
> another =3D
>> =3D3D
>>> =3D3D3D
>>>> way to fix this problem it would be much appreciated.
>>>> Ashley (KC1CPS)=3D3D3D