I'm a member of that club, former president in fact. The pl tone is 127.3 as
opposed to 67.0 for the bridgewater one you usually get in to and most
repeaters in the area. Are you 100% sure you have the tone set right?
Looking you up on QRZ, you shouldn't have any problem getting in to it from
there.
----- Original Message -----
From: "Ashley Bernard" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Tuesday, December 23, 2014 4:36 PM
Subject: Re: puxing 973 ht not receiving audio
> I=E2=80=99m currently at my actual house, not at school. trying to get =
> onto I think it=E2=80=99s K1SMH located in attleboro.
>> On Dec 23, 2014, at 4:31 PM, John Miller <[log in to unmask]> wrote:
>>=20
>> Are you not transmitting the right tone for the repeater? Are you =
> home? If=20
>> so which repeater is it? I may be able to help, were not far from each =
> other=20
>> and the closest repeaters to you at home I'm very familiar with.
>> John N1UMJ
>> ----- Original Message -----=20
>> From: "Ashley Bernard" <[log in to unmask]>
>> To: <[log in to unmask]>
>> Sent: Tuesday, December 23, 2014 4:14 PM
>> Subject: Re: puxing 973 ht not receiving audio
>>=20
>>=20
>>> The radios do hear each other. The problem is that when I let go of =
> the =3D
>>> PTT button on the Puxing I get no courtesy tone or sound of the =
> repeater =3D
>>> dropping, when in reality the transmission went through perfectly =
> fine =3D
>>> as I heard it 100 percent on my other radio.
>>> 73.
>>> Ashley KC1CPS
>>>> On Dec 23, 2014, at 4:11 PM, Colin McDonald <[log in to unmask]> =
> =3D
>>> wrote:
>>>> =3D20
>>>> OK.
>>>> SO can you hear your puxing transmitting, with your kenwood, on the =
> =3D
>>> repeater=3D20
>>>> input?
>>>> And vice versa? can you hear the kenwood transmitting on the =
> repeater =3D
>>> input=3D20
>>>> with the puxing?
>>>> Meaning only on the input frequency, not through the repeater.
>>>> Perhaps do this test on a simplex frequency to find out if the =
> radios =3D
>>> hear=3D20
>>>> each other.
>>>> You can trouble shoot these problems by eliminating one thing after =
> =3D
>>> another.
>>>> Any technical problem solving/trouble shooting must be done in a =3D
>>> liniar=3D20
>>>> fashion to remove each potential issue one at a time until you find =
> =3D
>>> the=3D20
>>>> problem.
>>>> =3D20
>>>> 73
>>>> Colin, V A6BKX
>>>> -----Original Message-----=3D20
>>>> From: Ashley Bernard
>>>> Sent: Tuesday, December 23, 2014 2:02 PM
>>>> To: [log in to unmask]
>>>> Subject: Re: puxing 973 ht not receiving audio
>>>> =3D20
>>>> yeah. it=3D3DE2=3D3D80=3D3D99s my radio. My kenwood is operating on =
> the same =3D
>>> =3D3D
>>>> repeater just fine.
>>>> =3D20
>>>>> On Dec 23, 2014, at 4:01 PM, Colin McDonald =
> <[log in to unmask]> =3D
>>> =3D3D
>>>> wrote:
>>>>> =3D3D20
>>>>> Ashley, is this on all repeater frequencies? or just one? could =
> the =3D
>>> =3D3D
>>>> machine=3D3D20
>>>>> be down or temperarily off the air for maintenance?
>>>>> It does happen.
>>>>> Do you have another radio to test your receive and transmit?
>>>>> =3D3D20
>>>>> 73
>>>>> Colin, V A6BKX
>>>>> =3D3D20
>>>>> -----Original Message-----=3D3D20
>>>>> From: Ashley Bernard
>>>>> Sent: Tuesday, December 23, 2014 1:36 PM
>>>>> To: [log in to unmask]
>>>>> Subject: Re: puxing 973 ht not receiving audio
>>>>> =3D3D20
>>>>> now I=3D3D3DE2=3D3D3D80=3D3D3D99ve reset, and am back to my =
> original =3D
>>> problem of =3D3D
>>>> not being =3D3D3D
>>>>> able to hear anything once I transmit. I=3D3D3DE2=3D3D3D80=3D3D3D99m =
> =3D
>>> definitely =3D3D3D
>>>>> transmitting now, just not being notified. I=3D3D3DE2=3D3D3D80=3D3D3D=
> 99ve =3D
>>> tried =3D3D
>>>> turning =3D3D3D
>>>>> off what you instructed to turn off but still =
> haven=3D3D3DE2=3D3D3D80=3D3D3D9=3D
>>> 9t =3D3D
>>>> solved the =3D3D3D
>>>>> issue yet.
>>>>> =3D3D20
>>>>>> On Dec 23, 2014, at 3:28 PM, Buddy Brannan <[log in to unmask]> =
> =3D3D
>>>> wrote:
>>>>>> =3D3D3D20
>>>>>> That sounds like you maybe are transmitting but changed your =
> offset =3D
>>> =3D3D
>>>> =3D3D3D3D
>>>>>> amount or direction.
>>>>>> =3D3D3D20
>>>>>> If you want to do a full reset, hold down menu while turning the =
> =3D3D
>>>> radio =3D3D3D
>>>>> =3D3D3D3D
>>>>>> on. Wait a second after the beep, and then let go. Press confirm =
> =3D3D3D=3D
>>>=20
>>>>> twice. =3D3D3D3D
>>>>>> That should reset everything but keep your memory channels =3D3D
>>>> intact.=3D3D3D3D20
>>>>>> =3D3D3D20
>>>>>> =3D3D3D3DE2=3D3D3D3D80=3D3D3D3D94=3D3D3D3D20
>>>>>> Buddy Brannan, KB5ELV - Erie, PA
>>>>>> Phone: 814-860-3194=3D3D3D3D20
>>>>>> Mobile: 814-431-0962
>>>>>> Email: [log in to unmask]
>>>>>> =3D3D3D20
>>>>>> =3D3D3D20
>>>>>> =3D3D3D20
>>>>>>> On Dec 23, 2014, at 3:25 PM, Ashley Bernard <[log in to unmask]> =
> =3D3D3D=3D
>>>=20
>>>>> wrote:
>>>>>>> =3D3D3D3D20
>>>>>>> so I did that, and now I don=3D3D3D3D3DE2=3D3D3D3D3D80=3D3D3D3D3D99=
> t =3D
>>> appear to =3D3D
>>>> be able =3D3D3D
>>>>> to =3D3D3D3D
>>>>>> transmit at =3D3D3D3D3D
>>>>>>> all. not sure what=3D3D3D3D3DE2=3D3D3D3D3D80=3D3D3D3D3D99s going =
> on.
>>>>>>> Thanks.
>>>>>>> Ashley
>>>>>>> =3D3D3D3D20
>>>>>>>> On Dec 23, 2014, at 2:37 PM, Buddy Brannan <[log in to unmask]> =
> =3D
>>> =3D3D3D3D=3D3D
>>>> =3D20
>>>>>> wrote:
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> Hi,
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> Likely you=3D3D3D3D3D3DE2=3D3D3D3D3D3D80=3D3D3D3D3D3D99ve turned =
> on =3D
>>> CTCSS =3D3D
>>>> squelch. Try =3D3D3D
>>>>> this:
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> 1) Press menu.
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> 2) Press the # key.
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> 3) Press Enter (next to menu).
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> 4) Press * twice. Then press the number 1. If you get a high =3D3D=
>
>>>> pitched =3D3D3D
>>>>> =3D3D3D3D
>>>>>> =3D3D3D3D3D3D=3D3D3D3D3D
>>>>>>> =3D3D3D3D20
>>>>>>>> tone with an error prompt, tones are all turned off. If you =3D
>>> =3D3D3D3D3D
>>>>>>> don=3D3D3D3D3D3DE2=3D3D3D3D3D3D80=3D3D3D3D3D3D99t,=3D3D3D3D3D3D
>>>>>>>> press * until you do.
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> 5) Press enter again.
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> 6) Rotate the selector knob once clockwise and repeat above =
> steps =3D
>>> =3D3D
>>>> to =3D3D3D
>>>>> =3D3D3D3D
>>>>>> =3D3D3D3D3D
>>>>>>> be =3D3D3D3D3D3D
>>>>>>>> sure receive CTCSS is off.=3D3D3D3D3D3D20
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> =3D3D3D3D3D3DE2=3D3D3D3D3D3D80=3D3D3D3D3D3D94=3D3D3D3D3D3D20
>>>>>>>> Buddy Brannan, KB5ELV - Erie, PA
>>>>>>>> Phone: 814-860-3194=3D3D3D3D3D3D20
>>>>>>>> Mobile: 814-431-0962
>>>>>>>> Email: [log in to unmask]
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> =3D3D3D3D3D20
>>>>>>>> =3D3D3D3D3D20
>>>>>>>>> On Dec 23, 2014, at 2:26 PM, Ashley Bernard <[log in to unmask]> =
> =3D3D=3D
>>>=20
>>>> =3D3D3D3D3D=3D3D3D
>>>>> =3D3D20
>>>>>>> wrote:
>>>>>>>>> =3D3D3D3D3D3D20
>>>>>>>>> Hi list,
>>>>>>>>> In my exploration with repeaters and radio operation, =
> =3D3D3D3D3D3D
>>>>>>>> I=3D3D3D3D3D3D3DE2=3D3D3D3D3D3D3D80=3D3D3D3D3D3D3D99ve=3D3D3D3D3D3=
> D3D
>>>>>>>>> managed to mess up my audio on my puxing ht. The speech output =
> =3D
>>> =3D3D3D
>>>>> works =3D3D3D3D
>>>>>> =3D3D3D3D3D
>>>>>>> =3D3D3D3D3D3D3D=3D3D3D3D3D3D
>>>>>>>> =3D3D3D3D3D20
>>>>>>>>> fine, and when I hit the PTT button I can tell my transmission =
> =3D3D
>>>> went =3D3D3D
>>>>> =3D3D3D3D
>>>>>> =3D3D3D3D3D
>>>>>>> =3D3D3D3D3D3D3D
>>>>>>>>> through by listening from another radio, but =3D3D3D
>>>>> I=3D3D3D3D3D3D3DE2=3D3D3D3D3D3D3D80=3D3D3D3D3D3D3=3D3D3D3D
>>>>>> D99m =3D3D3D3D3D
>>>>>>> =3D3D3D3D3D3D
>>>>>>>> receiving no =3D3D3D3D3D3D3D
>>>>>>>>> audio on the puxing side. If anyone knows a reset function or =3D=
>
>>> =3D3D3D3D
>>>>>> another =3D3D3D3D3D
>>>>>>> =3D3D3D3D3D3D
>>>>>>>> =3D3D3D3D3D3D3D
>>>>>>>>> way to fix this problem it would be much appreciated.
>>>>>>>>> Ashley (KC1CPS)=3D3D3D3D3D3D3D=3D3D20=3D20=20
|
