What kind of mount, nmo? You could put the wire around the threads
where the coil screws on. 19 inches should work. at least two would be
good.
73
Butch
WA0VJR
Node 3148
Wallace, ks.
On Sat, 17 Aug 2013, Tom Behler wrote:
> Mark:
>
> So, now I'm thinking of two things here.
>
> First, the magmount I have is sealed, so I'm not sure how I would get to the
> shield of the coax to make the connection you describe.
>
> Also, I'm doing some mental calculations as to the length of the
> counterpoise.
>
> Can someone refresh me as to the formula you would use for that, keeping in
> mind that I'd like the antenna to perform best around 146 megahertz--pretty
> much in the center of the band.
>
> Tom Behler: KB8TYJ
>
> ----- Original Message -----
> From: "Mark WZ0K" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Saturday, August 17, 2013 2:45 PM
> Subject: Re: 2-meter Antenna Challenge
>
>
>> Hi Tom,
>> On The antenna situation. Some years ago, I had a 5/8 wave mag mount
>> that I used in a window sill. It performed well enough. However, After
>> hearing about using a counterpoise, I loosened the antenna from the mag
>> mount and slid a thin piece of wire between the antenna and the mag mount.
>> I
>> made sure it touched the metal part of the bracket that was connected to
>> the
>> braid of the coax. The wire was cut to a quarter wave. Suddenly my reports
>> were better in all the repeaters, and I started reaching in to machines
>> that
>> I could not reach before. I hope this helps.
>>
>> God bless,
>> Mark
>> God loves You!
>> My personal website: Http://www.christiantraditions.info
>> The Blind Computer People List:
>> http://christiantraditions.info/mailman/listinfo/blindcomputerpeople_christiantraditions.info
>> Follow me on Twitter: https://twitter.com/TorgersonMark?refsrc=email
>> -----Original Message-----
>> From: [log in to unmask]
>> Sent: Saturday, August 17, 2013 11:32 AM
>> To: [log in to unmask]
>> Subject: Re: 2-meter Antenna Challenge
>>
>> Two suggestions:
>>
>>
>>
>>
>>> Hi, all.
>>>
>>> I hope I am not wearing out my welcome back to the list, but I have a
>>> challenging antenna situation I'm currently facing in the new faculty
>>> office
>>> I will be occupying starting this Spring semester.
>>>
>>> I currently have an old Kenwood TMV7A in the office, with which I have
>>> always had at least some luck, in terms of getting into our local 2-meter
>>> repeater. The repeater is about 15 miles from the University.
>>>
>>> However, in my new office, I am finding that the small mag-mount antenna
>>> I
>>> have always used simply does not allow me to reach the repeater
>>> consistently. Currently, I have the magmount sitting on a small metal
>>> bracket on the window sill in the office. It is right next to the
>>> window,
>>> so I would think that should help. However, I do not have much of a
>>> ground
>>> plain for the magmount. I also think there is some de-sensing going on
>>> with
>>> the steel of the office building, and with other surrounding computer
>>> equipment in the office complex.
>>>
>>> I do have a filing cabinet on the other side of the office that I could
>>> use
>>> as a ground plane, but the top of the filing cabinet is too high, and
>>> there
>>> is not enough space between it and the office ceiling to accommodate the
>>> magmount antenna.
>>>
>>> This obviously is a very challenging situation, and I also have to be at
>>> least somewhat concerned with appearance, in terms of not having an
>>> ugly-looking antenna that might draw more attention to what I am trying
>>> to
>>> do than I might want.
>>>
>>> Do any of you have any suggestions as to how to help the mag-mount
>>> perform
>>> better in this situation?
>>>
>>> Or, might I be better off considering another type of antenna, such as a
>>> J-pole of some sort.
>>>
>>> I would appreciate any thoughts.
>>>
>>> Tom Behler: KB8TYJ
>>>
>>>
>>
>
>
|
