Frank,
Maybe you want to turn on auto mode? Menu 27.
Below is a very rough menu list that I took from the control software.
I think I actually did half with the caps lock on and half with the
caps lock off. I'm also sure some typos. Not sure when I will get
arount to clean it up, so use it as a reference, and not as Gospel.
73, Steve KW3A
Menu list for TS-590sg - from control software Jan 1 2016
000 Firmware
001 power on message
002 display brightness
003 backlight color
004 panel key response for double functions
volume
005 beep volume
006 sidetone volume
007 message playback volume
voice guide
008 voice guide volume
009 voice guide speed
010 voice guide language
011 auto announcement
TUNING
012
013 TUNING CONTROL RATE PER REVOLUTION
014FREQUENCY ROUNDING OFF WHEN USING MULTI CH CONTROL MHZ STEPS
015 MULTI CHANNEL 9 KHZ CHANGE IN BROADCAST BAND
016 SSB MULTI CH CONTROL
017 CW MULTI CH CONTROL
018 AM MULTI CH CONTROL
019 FM MULTIT CH CONTROL
020 SHIFTABLE RX FREQUENCY DURING SPRIT TRANSMISSION
MEMORY CHANNEL
021 NUMBER OF QUICK MEMORY CHANNELS
022 TUNABLE MEMORYRECALL CHANNEL FREQUENCIES
SCAN
023 PROGRAM SCANPARTIALY SLOWED
24 PROGRAM SLOW SCAN RANGE
025 PROGRAM SCAN HOLD
026 SCAN RESUME METHOD
AUTO MODE
027 AUTO MODE OPERATION
DSP
028 FILTER CONTROL IN SSB HIGH/LOW AND SHIFT WIDTH
029 FILTER CONTROL IN SSB DATA HIGH/LOW AND SHIFT WIDTH
030 AUTO NOTCH TRACKING SPEED
031 TX FILTER FOR SSB/AM LOW CUT
032 TX FILTER FOR SSB/AM HIGH CUT
033 TX FILTER FOR SSB DATA LOW CUT
034 TX FILTER FOR SSB DATA HIGH CUT
035 SPEECH PROCESSOR EFFECT
Equalizer
036 dsp tx equalizer
037 dsp rx equalizer
cw
038 electric keyer mode
039 keying priority over playback
040 cw pitch/sidetone frequency
041 cw rise time
042 cw weighting
043 reverse cw weighting
044 bug key function
045 reverse dot and dash keying
046 mic up / dwn function
047 auto cw tx when keying in ssb
048 frequency correction for ssb to cw change
049 no break in while adjusting keying speed
fsk
050 fsk shift
051 reversed fsk keydown polarity
052 fsk tone frequency
fm
053 fm mic gain
transverter
056 transverter powerdown transverter
tuner
057 tx hold when it completes the tuning
058 antenna tuner for reception
amplifier
059 hf amplifier control relay
060 50 mhz amplifier control relay
message
061 constant recording
062 playback repeat
063 playback intervaltime
split/transfer
064 transfer split frequency data to another transceiver
065 copy split frequency data to vfo
tx inhibit
066 tx inhibit
pc communications
067 comm port baud rate
068 usb port baud rate
external audio input/output
069 audio input line selection for data communications
070 audio source for send/ptt transmission inn data mode
071 audio level of usb input for data communications
072 audio level of usb output for data communications
073 audio level of acc2 input for data communications
074 audio level of acc2 output for data communications
075 mixing beep tones for acc2/usb audio output
external accessory control
076 vox operation with datausb/acc2
077 data vox delay time
078 vox gain for usbaudio input
079 vox gain for acc2
080 reversed pks polarity
081 busy frequency transmissionlockout
082 ctts mute control
083 psq output logic
084 psq source
085 drive out connector function
timer
086 auto power off
pf keys
087 front panel pf a
088 front panel pf b
089 rit key (pf)
090 xit key (pf)
91 cl key (pf)
92 multi ch for other than cw (pf)
93 multichannel for cw (pf)
094 mic pf 1
095 mic pf 2
096 mic pf 3
097 mic pf 4
98 mic down key (pf)
99 mic up key (pf)
** end **
On 1/30/2016 2:43 PM, Frank Ventura wrote:
> Steve, thank you very much for your help. Unfortunately, I can't seem to fi=
> nd a menu chart in accessible format. Specifically, I cannot figure out whi=
> ch menu choice turns on the feature that automatically sets the uSB/LSB whe=
> n you tune a frequency.
> Thanks again for all the help.
> Frank
>
> -----Original Message-----
> From: For blind ham radio operators [mailto:[log in to unmask]] =
> On Behalf Of Steve Forst
> Sent: Saturday, January 30, 2016 6:39 AM
> To: [log in to unmask]
> Subject: Re: TS590g question
>
> Frank,
>
> Glad it worked. One thing I forgot to mention: If you start the reset=20
> process and hear the voice asking if you want to reset, but you get cold=
> feet, you can abort the process by hitting any key other than the a/b key=
> . Or if you don't hit the a/b key to finish the reset within a few second=
> s, it will also abort.
>
> Off the top of my head, the front panels are pretty much the same.=20
> However on the SG, the 3 buttons in the upper right hand corner of the rad=
> io (RIT, XIT, and Clear) can be reset as pf keys in menus. Also the multi =
> knob can be pushed in and is set up as a pf key. Default is power level. =
> Push in the button, the voice will say "TX power" and you can turn the knob=
> to set power then push in button again to get out of power setup.
>
> The menus are totally different for the S and SG versions. Also the=20
> control software for the 2 radios from the Kenwood site is different for th=
> e 2 radios.
> 73 hope you enjoy the radio, Steve KW3A
>
> On 1/30/2016 1:25 AM, Frank Ventura wrote:
>> Steve, thank you very much. That worked like a charm. Can I assume the=20
>> fron=3D t panel chart from the 590s still applies to the 590g? You've=20
>> been a great =3D help.
>> Frank
>>
>> -----Original Message-----
>> From: For blind ham radio operators=20
>> [mailto:[log in to unmask]] =3D On Behalf Of Steve Forst
>> Sent: Friday, January 29, 2016 9:35 PM
>> To: [log in to unmask]
>> Subject: Re: TS590g question
>>
>> Frank,
>>
>> Reset is the same on both the 590s and 590sg.
>>
>> You want the a/b button which is to the right of the main tuning knob,=20
>> seco=3D nd row down and third button from the left.
>>
>> Turn the radio off. Pressand hold the a/b button while you power up=3D2=
> 0
>> the radio. Release both the power and a/b buttons. The voice will say=
> =3D20
>> "Full reset?". For a full reset, press the a/b button again at this time=
> . =3D
>> Radio will reset and jump to 14.000.
>>
>> If you want to do a VFO reset instead, follow the above instructions,=20
>> but w=3D hen the voice says "full reset?", turn the multi knob until she=
> =3D20
>> says "VFO reset?", then hit the a/b button again. This will reset a=3D2=
> 0
>> lot of the radio, but keep menus and memories intact.
>>
>> 73, Steve KW3A
>>
>>
>>
>> On 1/29/2016 8:45 PM, Frank Ventura wrote:
>>> Hi all, I have a loaner TS590g for evaluation. I would like to=20
>>> perform=3D20 a fu=3D3D ll reset. The directions on icanworkthis thing fo=
> r=20
>>> the 590s=3D20 don't seem to b=3D3D e the same. Can anyone give me=20
>>> directions for the 590g=3D
>> , including where the=3D3D
>>> correct buttons are located? Thanks, as I can't seem to find=20
>>> any=3D20 documenta=3D3D tion for this rig in accessible format.
>>> Frank
>>>
>>
>
|