And speaking of sailing, Tom, do you know what happened to Tom
Karnes who had a sailboat in SF bay and regularly took blind
folks on trips? 73, Jim WA6EKS
----- Original Message -----
From: Tom Fowle <[log in to unmask]
To: [log in to unmask]
Date sent: Tue, 10 Nov 2015 18:19:41 -0800
Subject: OT. sailboats for the disabled.
richard,
Actually there are several dingies designed for folks with no or
little
lower body movement. puff and sip controls for the sheets and
tiller and the
lot. Cost like sin though.
Tom Fowle WA6IVG
Past commodore BAADS the Bay Area Association of Disabled
Sailors.
On Tue, Nov 10, 2015 at 12:35:45PM -0800, Richard B. McDonald
wrote:
Tom, now that is funny - a sailboat for the disabled! LOL!
priceless indeed!
And, I think you are right on the painting matter too.
-----Original Message-----
From: For blind ham radio operators
[mailto:[log in to unmask]]
On Behalf Of Tom Fowle
Sent: Monday, November 09, 2015 7:07 PM
To: [log in to unmask]
Subject: Re: Using PVC as a Frame for My 10M Full Wave Loop
Antenna
It might make sense to paint something expensive like the
Steppir with
"EXPENSIVE" marine paint, but PVC is pretty cheap it'd probably
be cheaper
to replace the pvc every couple years or so rather than use
marine paint on
it.
Anything "MaARINE" is way expensive. like anything for the
"DISABLED" Gosh,
think what they must charge for sailboats for the disabled!
Yeah, been there
seen that!
Just my not very humble opinion. <GRIN
Tom Fowle WA6IVG
On Mon, Nov 09, 2015 at 09:51:34AM -0700, Alan R. Downing
wrote:
I haven't been following this thread, but if it hasn't already
been
suggested, I would suggest that you paint with some quality
marine
paint. I know guys that want to extend the life of their
SteppIr
tubes use marine paint because it isn't bothered by the elements
as
much as regular outdoor paint would be.
HTH
Alan - N7MIT
Alan R. Downing
Phoenix, AZ
-----Original Message-----
From: For blind ham radio operators
[mailto:[log in to unmask]]
On Behalf Of Richard B. McDonald
Sent: Monday, November 09, 2015 7:48 AM
To: [log in to unmask]
Subject: Re: Using PVC as a Frame for My 10M Full Wave Loop
Antenna
Yeah, Kent, painting is widely recommended. Some sort of a
latex
paint is best I suppose especially since I will put the wire
inside
the PVC. I guess it will come down to the cost differential
between
1) "Schedule 40" UV resistant PVC versus 2) non-UV resistant PVC
plus
the cost of the necessary paint.
-----Original Message-----
From: For blind ham radio operators
[mailto:[log in to unmask]]
On Behalf Of Kent Plemmons
Sent: Sunday, November 08, 2015 11:12 AM
To: [log in to unmask]
Subject: Re: Using PVC as a Frame for My 10M Full Wave Loop
Antenna
Hi,
Don't use the "black", that is not PVC but rather ABS. When the
sun
hits ABS it will bow due to it being black and the side of the
pipe
that is directly exposed to the sun will expand causing a bow.
PVC
that is gray is generally used as electrical conduit and offers
some
characteristic that greatly reduces static that might build up
in a
wire. Pretty much any PVC will work but I personally would
paint it.
Kent, KK4FFF, Clyde NC
-----Original Message-----
From: For blind ham radio operators
[mailto:[log in to unmask]]
On Behalf Of Richard B. McDonald
Sent: Sunday, November 08, 2015 12:47 PM
To: [log in to unmask]
Subject: Re: Using PVC as a Frame for My 10M Full Wave Loop
Antenna
Hi Tom!
thanks for this. Right - "Schedule 40" PVC it shall be!
Incidentally, is it grey? Someone said to use the "grey" PVC
for its
UV resistance; and another member of this list said to avoid the
"black" PVC for its carbon content.
As far as placement of the loop, I am planning just to place it
atop
my shack's roof. The roof is flat with a ~3% slant, and ~13'
high.
73,
Richard KK6MRH
-----Original Message-----
From: For blind ham radio operators
[mailto:[log in to unmask]]
On Behalf Of Tom Fowle
Sent: Saturday, November 07, 2015 5:44 PM
To: [log in to unmask]
Subject: Re: Using PVC as a Frame for My 10M Full Wave Loop
Antenna
richard,
To clarify another post, you need to use "Schedule 40" pvc which
is U.V.
resistant.
I'd think each segment of your loop won't be much more than 2
meters long.
I'd kind of doubt you'll need reinforcemment for that
relatively
small setup, but you could also use a few extra rope supports
depending on how you're going to support the loop.
There shouldn't be any; issue with running the wire inside the
pipe,
except kind of a tangle while assembling everything on the long
wire.
How do you plan to support the loop?
Tom Fowle WA6IVG
On Sat, Nov 07, 2015 at 05:14:52PM +0000, R Bernstein wrote:
Use uv-resistant PVC. Reinforce it inside with wooden dowels or
possibly 3=
/4 inch PVC.
73, Rick W3GWU
________________________________________
From: For blind ham radio operators
[[log in to unmask]]
on beha= lf of Richard B. McDonald [[log in to unmask]]
Sent: Saturday, November 7, 2015 9:11 AM
To: [log in to unmask]
Subject: Using PVC as a Frame for My 10M Full Wave Loop Antenna
Hi!
So, I am planning to make my RX only 10M (28.4 MHZ) full wave
loop
antenna into an octagon shape. My wire is insulated 14 gauge
stranded
copper wire.
I intend to use ~1.0" diameter PVC pipe for a frame. About PVC
pipe, does it matter if I 1) put the wire inside the pipe or 2)
tape
it to the outside of the pipe? I prefer putting the wire inside
the
pipe.
However, are ther= e any RF interference issues with PVC? Also,
I
wonder how PVC will hold-up t= o the elements - particularly UV
light (sunlight)?
73,
Richard KK6MRH
|