U r welcome
Sent from my iPod
On Apr 26, 2015, at 7:42 AM, Junior Lolley <[log in to unmask]> wrote:
> Danny, thanks very much.
>
>
> Junior Lolley kg4itd
> Liberty County Emergency Coordinator
> "The 3 C=E2=80=99s of life: choices, chances, and changes. You must make =
> a choice to take a chance or your life will never change."
>
>
> -----Original Message-----
> From: For blind ham radio operators =
> [mailto:[log in to unmask]] On Behalf Of Dan B Dyer Jr,/Danny
> Sent: Saturday, April 25, 2015 9:59 PM
> To: [log in to unmask]
> Subject: BuddysUv5REyesFreeGuide,Baofeng UV-5R Menu Options and =
> choicesAsWellAsDCS Table.
>
> http://buddy.brannan.name/Baofeng-UV5R-eyes-free.rtf
> Baofeng UV-5RTips And Hints For Eyes-Free Operation
>
> Buddy Brannan, KB5ELV, [log in to unmask]
>
> Last Updated: 8 May 2012
>
> The Baofeng UV-5R is an inexpensive dualband handheld radio, operating =
> on 2M and 70CM. This radio may be of interest to blind hams, since =
> (unlike more expensive radios from the big three manufacturers) Baofeng =
> has managed to implement limited speech feedback for some functions. =
> While we would wish for more, such as voice confirmation of frequency, =
> CTCSS/DCS settings, and so on, this radio provides a very usable =
> alternative to other, more expensive handhelds from the traditional =
> manufacturers.
>
> Please feel free to distribute this document. please send additions,=20
> corrections, or modifications to me via Email to [log in to unmask]
>
> Thanks.
>
> Any additions, corrections, clarifications, or suggestions are =
> gratefully accepted. Please Email them to me for inclusion or =
> incorporation into this guide. I can be reached by Email at:
>
> Email: [log in to unmask]
>
> Notably, a menu listing would be very much appreciated. I believe I can =
> piece it together from the manual, but if someone already has it or can =
> quickly throw it together, I'd appreciate it. Also, accurate key labels =
> would be appreciated, especially where I don't have them.
>
> The latest version of this document can be had here:
>
> http://buddy.brannan.name/baofeng-uv5r-eyes-free.rtf
>
> Acknowledgements
>
> Thanks to the following fine folks for their assistance:
>
> =C3=A2=E2=82=AC=C2=A2 Ed Griffin, W4KMA, at Import Communications
> (http://www.importcommunications.com) for providing the initial Baofeng =
> manual, as well as for orientation to the radio's keypad.
>
> =C3=A2=E2=82=AC=C2=A2 All the folks on the Baofeng UV-5R Yahoogroup for =
> hints on programming and use, as well as on getting around the radio's =
> many little quirks.
>
> =C3=A3=E2=82=AC=E2=82=AC
>
> Inserting the Battery
>
> The battery attaches to the back of the radio, very like many other =
> handheld radios and mobile phones.
>
> =C3=A2=E2=82=AC=C2=A2 Place the radio facedown in front of you and the =
> top of the radio facing away from you.
>
> =C3=A2=E2=82=AC=C2=A2 The battery pack is rectangular, with a plastic =
> tab at the top center of the pack. The back of the battery, toward the =
> bottom edge, has three contacts for charging in the included drop-in =
> charger.
>
> =C3=A2=E2=82=AC=C2=A2 Line the top of the battery up with the bottom of =
> the radio so that the top of the battery rests on top of the bottom edge =
> of the radio, with the charging contacts facing up. Then, slide the =
> battery away from you, towards the top of the radio. You will feel the =
> battery slide up the guides on the radio and then latch in place as the =
> latch in the radio connects to the tab at the top of the battery.
>
> Attaching the Belt Clip
>
> The belt clip attaches to the back of the radio with two included =
> Philips head screws, which will be screwed into the back of the radio, =
> towards the top, just above the top of the battery pack.
>
> Remove the screws from the back of the radio. Put them into the holes on =
> the sides of the hinged plate on the back of the belt clip. It might be =
> easiest to do these one at a time, as the screws are fairly small.
>
> Line the screws in the belt clip up with the holes in the radio. I found =
> this a little tricky, as it's necessary to squeeze the belt clip open so =
> that the plate with the screws in it is flat only when the belt clip is =
> squeezed open. Screw in one of the screws partially, so that the clip =
> holds in place, then start the other. Tighten both once the belt clip is =
> properly aligned. It's a little tricky and feels like you need an extra =
> hand.=20
> Fortunately, once it's done, you won't have to do it again.
>
> Orientation
>
> Stand the radio up with the keypad facing you. Naturally, the keypad =
> will be the front of the radio, and we will discuss the radio in this =
> orientation.
>
> At the top of the radio, you'll find an SMA male antenna jack on the =
> left and the on/off/volume knob on the right. Between these is a large =
> LED flashlight bulb. Behind the LED is the battery release latch. Push =
> the release latch forward and slide the battery down to remove it.
>
> The right side of the radio only has the loop for the wrist strap and =
> the speaker/mic jacks. The speaker/mic jacks are located under a cover =
> that swings open towards the back. Pull the front of the cover free with =
> a thumbnail to open it and plug in either a speaker/mic or programming =
> cable.
>
> The left side of the radio has three buttons. From top to bottom, they =
> are the FM radio key, the PTT key, and the Monitor key.
>
> The FM radio key turns on the FM radio if pressed briefly. If this =
> button is held, it will turn on a pretty annoying alarm siren.
>
> The PTT button keys the radio.
>
> The monitor button, if held, will open the squelch for as long as the =
> button is held in. If it is pressed quickly, it turns on (or off) the =
> LED light at the top of the radio. Unfortunately, both "On" and "Off" =
> play the same tone, so there is no non visual way to know whether the =
> light is on or not.
>
> The front of the radio is where we will focus most of our attention. At =
> the top of the front panel is the LCD display. Directly below the =
> display is one button at the left side of the front panel. It is =
> labeled, "VFO/M R.
>
> This is the button that toggles between "Frequency mode" (VFO) and =
> "Channel mode" (Memory channels). You will also find a generous speaker =
> grille, with a hole right below the button for the microphone.
>
> Below the speaker are two more buttons, one on the left side of the =
> front panel and one on the right. The left button is the A/B button, =
> which switches from the "A", or top display frequency or channel, to the =
> "B", or bottom, frequency or channel. Since most programming functions =
> can only be done from the "A" side, we won't do much with this button. =
> Also, be aware that there is no audible indication as to whether you =
> have switched to "A"=20
> or "B". The only way you'd know would be by trying to program a memory =
> and having the memory not program.
>
> The button on the right side of the display is the "Band" button. This =
> determines whether you are entering VHF or UHF frequencies. This button =
> has no effect at all in channel mode.
>
> =C3=A3=E2=82=AC=E2=82=AC
>
> Below these two buttons is what looks like a traditional DTMF keypad, =
> having four rows of four buttons each.
>
> This keypad, however, isn't exactly traditional in its layout. The top =
> four buttons are the "menu" button (used to open the settings menu), the =
> "up"=20
> button, the "down" button, and the "cancel" button. In transmit, these =
> buttons send A, C, B, and D DTMF tones, respectively. Below these, you =
> will find (left to right, top to bottom): 1, 2, 3, and scan/reverse =
> (which is also the star key); 4, 5, 6, 0; 7, 8, 9 lock (which sends =
> pound).
>
> Turning the Radio On
>
> To turn the radio on, turn the power/volume knob to the right until it =
> clicks on. You will hear two short beeps, followed by an announcement of =
> the radio's mode. You will hear "Frequency mode" for VFO mode or =
> "Channel mode"=20
> for memory mode. The first time you turn the radio on, it will be in =
> "Frequency" mode with "dual" receive mode enabled.
>
> In order to make using this radio a little easier, I recommend turning =
> off the "Dual" receive option. Once turned off, this setting will be =
> remembered permanently. It can always be turned back on if you want or =
> need it.
>
> Press "Menu". The radio will say "Menu".
>
> Press "7", then press "Menu". The radio will say "Dual stand by". Yes, =
> really. She's hard to understand sometimes, but that's what she's =
> saying.
>
> Press "0", then press "Menu". The radio will say "Confirm".
>
> Finally, press "Cancel" to exit the menu.
>
> I have been putting the "dual" in quotes, because it isn't really dual =
> receive. It's more like dual watch, because audio from only one channel =
> or the other is heard at any given time.
>
> To further complicate the issue, there is an option to have the transmit =
> follow whichever channel (A or B) opens the receiver. If this option is =
> turned on, it may be difficult to know where exactly you are =
> transmitting.=20
> On the whole, it's probably best to just turn the dual function off.
>
> A Couple Other Initial Setup Tasks
>
> There are a couple of options that are turned on by default that it's =
> best to turn off. Having these on will make operating the radio annoying =
> either to you or to the people you're talking to.
>
> There are three settings for eliminating repeater tail tones or courtesy =
> tones. It is not exactly clear what the differences are in these =
> settings, but you want to turn them all off. There is also a "roger =
> beep" setting that you also want to disable. These are menus 35, 36, 37, =
> and 39. Set all of these entries to 0:
>
> =C3=A2=E2=82=AC=C2=A2 Press "Menu", "3", "5", "Menu", "0", "Menu".
>
> =C3=A2=E2=82=AC=C2=A2 Press "Menu", "3", "6", "Menu", "0", "Menu".
>
> =C3=A2=E2=82=AC=C2=A2 Press "Menu", "3", "7", "Menu", "0", "Menu".
>
> =C3=A2=E2=82=AC=C2=A2 Press "Menu", "3", "9", "Menu", "0", "Menu".
>
> A Note About the Menu Key
>
> -
>
> When the Menu key is pressed, the radio will say "Menu". This key also =
> functions as "Enter". Thus, after modifying a menu option, press the =
> Menu key again to accept the change. The radio will say "Confirm" to =
> acknowledge a change in a menu's parameters.
>
> Changing Channels Or Frequency
>
> You can set the frequency by using the up/down buttons or by entering =
> the frequency or channel number directly. Note that the numbers speak =
> when pressed. Enter six digits for frequency, i.e. 146520 or 444100, and =
> three digits for the channel number, i.e. 001, 024, or 114.
>
> (Since only six digits can be entered in the frequency field, entering =
> frequencies containing more than six digits is accomplished by adjusting =
> the "step frequency"/Menu option 1, then using the up-down keys.
>
> frequencies in a 6.25 KHz channel spacing, like 467.7125, enter six =
> digits, such as 467.712. If you have the channel spacing (Menu 1) set to =
> 6.25 KHz,/ the radio will set the channel correctly. For frequencies in =
> a 2.5 KHz channel spacing, such as 154.5275 set the radio to 154.525 =
> and, with a 2.5 KHz channel spacing (Menu 1, option 0) press the "Up" =
> button once.
>
> (In menu 1, Step Frequency Option,
>
> 0 =3D 2.5 KHz
> 1 =3D 5 KHz
> 2 =3D 6.25 KHz
> 3 =3D 10 KHz
> 4 =3D 12.5 KHz
> 5 =3D 25 KHz.)
>
>
> See the menu section below for a more complete discussion of setting =
> menu parameters.
>
>
>
>
>
> Programming Memories
>
> You can program memories either with a standard split or with odd =
> splits.=20
> Remember that once a memory is programmed, it cannot be changed, short =
> of=20
> deleting it and starting over. Memories store receive and transmit=20
> frequencies, along with receive and transmit CTCSS or DCS codes and =
> channel=20
> width (wide or narrow). Power level can be changed in memory mode.
>
> Programming a repeater channel with standard offsets:
>
> 1 Choose the "A" frequency, printed on the top line of the display. This =
> is=20
> probably already done, but if you go through all the steps to program =
> and=20
> get a single beep upon the final press of "Menu", you are in the B VFO =
> and=20
> need to press the "A/B" button.
>
> 2 If you are in channel mode, press the channel/frequency button. =
> Remember,=20
> channel mode will speak the channel number if you press the "up" or =
> "down"=20
> button.
>
> 3 Ensure you are on the correct band. If you enter a frequency and the =
> radio=20
> says "Cancel" when you press the last digit, press the "Band" button to=20
> select the correct band.
>
> 4 Enter the repeater output frequency, such as 147060.
>
> 5 Press "Menu", "2", "6", "Menu". The radio will say "Offset frequency".
>
> 6 For 2 meter repeaters, enter 00600. For 70 cm repeaters in the US or=20
> Canada, press
>
> 05000. This may be different in other parts of the world.
>
> 7 Press "Menu", "2", "5", "Menu". The radio will beep but will say =
> nothing.
>
> 8 Press "0" for a 0 or Simplex offset, "1" for a plus (positive) offset, =
> or=20
> "2" for a minus (Negative) offset, then press "Menu". The radio will say =
>
> "Confirm".
>
> 9 Set the CTCSS or DCS codes for transmit and receive, as appropriate. =
> These=20
> are in menus 11 and 12 for CTCSS and DCS receive respectively, and menus =
> 13=20
> and 14 for CTCSS and DCS transmit. CTCSS tones can be entered directly; =
> for=20
> instance, enter 885 for an 88.5 Hz tone, 1318 for a 131.8 tone, etc. See =
>
> below for a list of DCS codes.
>
> 10 If the menu has exited, indicated by two very short bleeps, one =
> higher=20
> followed by one slightly lower, press the Menu key to re-enter the menu. =
>
> This should not be necessary often, as the menu stays up for close to 10 =
>
> seconds before timing out.
>
> 11 While in the menu, press 2, 7, Menu. The radio will say "memory =
> channel".
>
> 12 Enter a channel number from 000 to 127. However, be sure not to use a =
>
> channel number that has already been programmed since the radio will not =
> let=20
> you overwrite a stored memory. Programming over a channel with data in =
> it=20
> will simply change that channel's transmit frequency. Once the channel=20
> number is entered, press "Menu" again. The radio will say "Receiving=20
> memory".
>
> 13 Press "Exit".
>
> 14 Press the "Scan/Rev" button. This will swap over the transmit and =
> receive=20
> frequencies so that they are reversed. This is handy for listening to =
> the=20
> repeater's input channel, in order to determinee whether a station is in =
>
> simplex range or not.
>
> 15 Press "Menu", "2", "7", "Menu". The radio will say "Memory channel".
>
> 16 Enter the same memory channel you entered above in step 12. Then =
> press=20
> "Menu" again. The radio will say "Transmitting memory".
>
> 17 Press "exit". You've set up a repeater channel. You will find it in =
> your=20
> list of program channels when you switch to channel mode.
>
> Programming A Repeater With An Odd Split
>
> Alternatively, you can specify your own transmit and receive =
> frequencies. In=20
> brief, you would program in the receive frequency first, then program in =
> the=20
> transmit frequency in the same way. This may be more reliable, since =
> only=20
> the "A" display works for programming memories, thus, the radio can only =
>
> remember one offset value for programming purposes. For this method, the =
>
> offset value (memory 26) and offset direction (menu 25) don't matter at =
> all.
>
> To demonstrate, here is how you would program in the infamous 147.435=20
> repeater in Los Angeles into memory 99. This repeater has an output=20
> frequency of 147.435 and an input frequency of 146.400, a decidedly very =
> odd=20
> split. As there is no CTCSS tone, we won't worry with that in this =
> example.
>
> 1 If in channel mode, press the "VFO/MR" button at the top left corner =
> of=20
> the front panel. to switch to Frequency Mode.
>
> 2 Press 1, 4, 7, 4, 3, 5.
>
> 3 Press Menu, 2, 7, Menu. The radio will say "Channel Memory". Then, =
> type 0,=20
> 9, 9, Menu. The radio will say "Receiving memory".
>
> 4 Press cancel to exit the menu.
>
> 5 Press 1, 4, 6, 4, 0, 0.
>
> 6 Press menu, 2, 7, menu. The radio will say "Channel memory".
>
> 7 Press 0, 9, 9, Menu. The radio will say "Transmit memory".
>
> 8 Press "Exit".
>
> 9 The odd split is now programmed.
>
> Again, remember that you can use this same procedure to program standard =
>
> offsets, too. As long as you know the repeater's input and output, you =
> can=20
> program them separately if you wish, and not worry about the repeater=20
> offsets.
>
> Changing Between VFO And Memory Modes
>
> You can switch easily between VFO ("Frequency") mode and memory =
> ("Channel")=20
> mode by pressing the top most button on the front of the transceiver. =
> The=20
> voice will tell you whether you are in "channel mode" or "Frequency =
> mode".=20
> Channel mode must have at least one channel programmed; there are at =
> least=20
> two programmed from the factory. Incidentally, it's probably a good idea =
> to=20
> delete those channels and put your own data in them immediately. =
> Deleting=20
> channels is done with menu 28.
>
> A channel can be directly set by entering it's three digit number on the =
>
> keypad, such as 005, 022, or 122 for channel 5, 22, or 122 respectively. =
> The=20
> new channel number will be announced via a voice prompt.
>
> Adjusting Menu Options
>
> All menu options can be adjusted from the keypad. You can either scroll=20
> through the menu with the up/down buttons, or by directly selecting the =
> menu=20
> option you want numerically. So that you can most easily keep track of =
> where=20
> you are, I believe selecting options numerically is easiest, as there =
> is,=20
> again, no audible indication of when the beginning or end of the menu is =
>
> reached, and the menus wrap. Note that the menu begins with 0, not with =
> 1.=20
> Menu 0 is the squelch adjustment.
>
> As with selecting menus, the menu options can be adjusted numerically. =
> For=20
> instance, selecting menu 2 (to adjust the power level), press 0 for high =
>
> power or 1 for low power. For offset direction (menu 25), you can select =
> 0=20
> for no offset, 1 for a plus offset, or 2 for a minus offset. So, as menu =
>
> options below are listed, the first option is always number 0, not =
> number 1.
>
> To adjust the menus, press the Menu key, which is the first key on the =
> first=20
> row of the main keypad. You will hear "Menu", at which time you can then =
>
> enter a menu number or press the up/down buttons. Once you reach the =
> menu=20
> you want, press the Menu key again. In most, though not all, cases,, you =
>
> will hear voice confirmation of the name of the menu item you have =
> selected.=20
> In the cases where you do not hear a voice confirmation, you will just =
> hear=20
> a beep. Adjust the parameter by pressing numbers or up/down arrows. Once =
> the=20
> menu is set correctly, press the Menu key again. You will hear the word=20
> "Confirm" spoken to indicate that the option is set. You can then choose =
>
> another menu item or press the cancel button to exit the menu. If you do =
>
> nothing for about 10 seconds, the menu will exit automatically. In =
> either=20
> case, you will hear a tone to confirm you are no longer in the menu =
> system.
>
>
>
>
>
> Two, Baofeng UV-5R Menu Options and choices
>
>
>
> 0, squelch level: 0-9
>
>
>
> 1, frequency step: 2.5, 5, 6.25, 10, 12.5, and 25
>
>
>
> 2, transmit power: high/low
>
>
>
> 3, battery save: off, 1, 2, 3, 4, 1:1, 1:2, 1:3, 1:4
>
>
>
> 4, vox: off, 0-10
>
>
>
> 5, wideband/narrowband: wide, narrow
>
>
>
> 6, abr, display illumination: off, 1, 2, 3, 4, 5 seconds
>
>
>
> 7, tdr, dual watch reception: off/on
>
>
>
> 8, keypad beep: off, on
>
>
>
> 9, tot (transmission timer) 15, 30, 45, 60, ''' 585 and 600 seconds
>
> (note) the manual shows dot, dot, dot, between 60 and 585 seconds.
>
> I assume this means it can be set in 15 second increments between these=20
> values.
>
>
>
> 10, rdcs, reception digital coded squelch
>
>
>
> 11, rcts, reception continuous tone coded squelch
>
>
>
> 12, tdcs, transmission digital coded squelch
>
>
>
> 13, tcts, transmission continuous tone coded squelch
>
>
>
> 14, voice prompt: off/on
>
>
>
> 15, ani, automatic number identification of the radio: can only be set =
> by pc=20
> software
>
>
>
> 16, dtmf st, dtmf tone of transmitting code: off, dt-st, ani-st, dt+ani
>
>
>
> 17, s code, signal code: only could be set by pc software
>
>
>
> 18, sc rev, scan resume method: to, co, se
>
>
>
> 19, push to talk id: off, bot, eot, both
>
>
>
> 20, ptt lt, delay the signal code sending, 0-30 ms
>
>
>
> 21, mdf-a, (under channel mode the channel displays) frequency, channel, =
>
> name, only set by pc software
>
>
>
> 22, mdf-b, same as menu 21, for b band
>
>
>
> 23, bcl, busy channel lockout: off/on
>
>
>
> 24, auto lk, keypad locked automatically: off/on
>
>
>
> 25, sftd, direction of frequency shift: off, plus, minus
>
>
>
> 26, offset, frequency shift: 0-69.990 mhz
>
>
>
> 27, memch, store memory channels: 000-127
>
>
>
> 28, delch, delete memory channel: 000-127
>
>
>
> 29, wt-led, illumination display color of stand by: off, blue, orange,=20
> purple
>
>
>
> 30, rx-led, illumination display color of reception: off, blue, orange,=20
> purple
>
>
>
> 31, tx-led, illumination display color of transmission: off, blue, =
> orange,=20
> purple
>
>
>
> 32, al-mod, alarm mode: site, tone, code
>
>
>
> 33, band, band selection: vhf, uhf
>
>
>
> 34, tx-ab, transmitt+ selection while in dual watch/reception: off, a, b
>
>
>
> 35, ste, tail tone elimination: off/on
>
>
>
> 36, rp_ste, tail tone elimination in communication through repeater: =
> off,=20
> 1-10
>
>
>
> 37, rpt_rl, delay of tail tone of repeater: off, 1-10
>
>
>
> 38, ponmgs, boot display: full, mgs
>
>
>
> 39, roger, tone end of transmission: off/on
>
>
>
> 40, reset, restore to default setting: vfo, all
> The command to RESET ALL is: menu 40 menu menu menu
>
>
> Three,
>
>
>
>
>
>
>
> DCS
>
> WITH ASSOCIATED KEYPAD NUMBERS
>
> 000: Off
>
> 001: D023N
>
> 002: D025N
>
> 003: D026N
>
> 004: D031N
>
> 005: D032N
>
> 006: D036N
>
> 007: D043N
>
> 008: D047N
>
> 009: D051N
>
> 010: D053N
>
> 011: D054N
>
> 012: D065N
>
> 013: D071N
>
> 014: D072N
>
> 015: D073N
>
> 016: D074N
>
> 017: D114N
>
> 018: D115N
>
> 019: D116N
>
> 020: D122N
>
> 021: D125N
>
> 022: D131N
>
> 023: D132N
>
> 024: D134N
>
> 025: D143N
>
> 026: D145N
>
> 027: D152N
>
> 028: D155N
>
> 029: D156N
>
> 030: D162N
>
> 031: D165N
>
> 032: D172N
>
> 033: D174N
>
> 034: D208N
>
> 035: D212N
>
> 036: D223N
>
> 037: D225N
>
> 038: D226N
>
> 039: D243N
>
> 040: D244N
>
> 041: D245N
>
> 042: D246N
>
> 043: D252N
>
> 044: D252N
>
> 045: D255N
>
> 046: D261N
>
> 047: D263N
>
> 048: D265N
>
> 049: D266N
>
> 050: D271N
>
> 051: D274N
>
> 052: D306N
>
> 053: D311N
>
> 054: D315N
>
> 055: D325N
>
> 056: D331N
>
> 057: D332N
>
> 058: D343N
>
> 059: D346N
>
> 060: D351N
>
> 061: D356N
>
> 062: D364N
>
> 063: D365N
>
> 064: D371N
>
> 065: D411N
>
> 066: D412N
>
> 067: D413N
>
> 068: D423N
>
> 069: D431N
>
> 070: D432N
>
> 071: D445N
>
> 072: D446N
>
> 073: D452N
>
> 074: D454N
>
> 075: D455N
>
> 076: D462N
>
> 077: D464N
>
> 078: D465N
>
> 079: D466N
>
> 080: D503N
>
> 081: D506N
>
> 082: D516N
>
> 083: D523N
>
> 084: D526N
>
> 085: D532N
>
> 086: D546N
>
> 087: D565N
>
> 088: D606N
>
> 089: D612N
>
> 090: D624N
>
> 091: D627N
>
> 092: D631N
>
> 093: D632N
>
> 094: D645N
>
> 095: D654N
>
> 096: D662N
>
> 097: D664N
>
> 098: D703B
>
> 099: D712N
>
> 100: D723N
>
> 101: D731N
>
> 102: D732N
>
> 103: D734N
>
> 104: D743N
>
> 105: D754N
>
> =C3=A3=E2=82=AC=E2=82=AC
>
> --
>
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 2015.0.5646 / Virus Database: 4334/9630 - Release Date: =
> 04/26/15
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 2015.0.5646 / Virus Database: 4334/9630 - Release Date: =
> 04/26/15
|