Hi, Steve. Well, the transmitter keyed up and the tone went out on
PSK/Digipan. However, the speech keeps reading "200, 300" etc., no
matter how carefully I tune to the tone.
Also, in either mtty or Digipan, should I adjust the gain? And
unless I'm missing something, can't get the filter to go to 3000.--Matt, N1IBB.
P.S. Haven't felt compelled to either light the fuse on the 480, or
take it to the shooting range.
At 02:52 PM 7/19/2015 -0400, you wrote:
>I think the only thing you need to do is figure out why the interface
>isn't keying the radio.
>
>
>Since you have Digipan on your pc, in the configuration menu, under
>soundcards, select the USB sound device for both RX and TX. Also under
>the configuration/serial ports menu, select "none". Press f9 and the
>radio should key and the psk tones transmitted
>
>If this works, then your RTTY problems are in the MMTTY settings. If
>it doesn't key in Digipan, then the problem is probably in the
>interface. Not installed, connected, or adjusted right.
>
>
>MMTTY only does RTTY and Digipan does PSK. You can try the trial
>version of MixW which John uses. It is multimode, but I never got it
>working here. Until you get the hardware figured out, you might want to
>hold off on any software that has a trial period, since you can't take
>full advantage of it. The cd that came with the SL may have had some
>other software on it.
>
> BTW, I stick to RTTY and haven't done any psk in years, so of course
>I'm an expert.
>
>If need be, find the fuse on the 480 and light it.
>73, Steve KW3A
>
>
>On 7/19/2015 2:28 PM, Matthew Chao wrote:
> > Hi, Steve. Thanks. Will be looking for PSK and follow your
> > suggestions. Besides opening up the filter and turning on Menu 45,
> > is there anything else I need to do on my 480?
> >
> > Also, will mmtty do psk, and are there any settings I need to change
> > for that to work? I also have digipan and have same questions about
> > that one as well. Can digipan do RTTY? Thanks.--Matt.
> >
> > At 01:09 PM 7/19/2015 -0400, you wrote:
> >> Matt,
> >>
> >> Glad you got something working. The wav files are nice, but you
> >> will have to start tuning in real signals.
> >>
> >> Not sure how much monkeying around with the screen will help.
> >> Tinker if you want, you can always untinker later.
> >>
> >> The left knob is TX audio and the middle knob is RX audio. You might
> >> want to try increasing the TX (left knob) and decrease the VOX (right
> >> knob) and see if you can get the radio to key.
> >>
> >> You can hear PSK on 20 meters anytime the band is open, between 14.070
> >> and 14.073 If you are on 14.070 use USB mode, if on 14.073 use LSB mode.
> >>
> >>
> >> Open the filter in the radio to 3 khz. The psk software will grab all
> >> the signals in that 3 khz for decoding.
> >>
> >> Have fun, Steve KW3A
> >>
> >>
> >> On 7/19/2015 12:27 PM, Matthew Chao wrote:
> >>> Ok, Steve, we got receive back. Readjusted everything according to
> >>> instructions. Also under the sl/usb codec speaker settings, changed
> >>> freq response to 11025. ARan test again, and it's reading the files.
> >>>
> >>> Does it help if I size the creen by character width and line height
> >>> under mtty? Also, anywhere I can get sounds of PSK31 so as to know
> >>> what to listen for?
> >>>
> >>> Also, which knobs on the signallink do what? Far right is
> >>> vox? Other two knobs set pointing straight up.
> >>>
> >>> Oh, no smoke yet - but wait ... there's more!--Matt, N1IBB.
> >>>
> >>> t 09:06 AM 7/19/2015 -0400, you wrote:
> >>>> Matt,
> >>>>
> >>>> Too much junk in RTTY is usually to much drive to the sound card. The
> >>>> RTTY contests are over and it will be harder to find a
> signal on the
> >>>> air to decode. On to PSK!.
> >>>>
> >>>> You're jumping back and forth between RX and TX and don't seem to have a
> >>>> handle on either one.
> >>>>
> >>>> When you transmit and hear tones, are they coming from the radio, or
> >>>> the pc's speakers?
> >>>>
> >>>> If from the radio (tones from radio, but not going into TX) it's a
> >>>> vox/tx drive issue. If the tones are coming out of the pc's speakers,
> >>>> I think you may not have the right sound card selected and are trying
> >>>> to transmit on the pc's sound card.
> >>>>
> >>>> The fact that you saw some call signs yesterday, would lead me to think
> >>>> you are at least hooked up correctly, with the mini din plugged into the
> >>>> center jack of the 3 behind the little cover. It's a snug fit. Are you
> >>>> sure it is plugged in firmly? On mine, the little notch on the metal
> >>>> barrel of the plug is at the 12 o'clock position.
> >>>>
> >>>> Don't worry, it's all just a bad dream.
> >>>>
> >>>> 73, Steve KW3A
> >>>> On 7/19/2015 8:44 AM, Matthew Chao wrote:
> >>>>> No smoking or zapping sounds yet. Adjusted the volume, and now, I'm
> >>>>> getting garbled characters. Probably should have left well enough
> >>>>> alone, but had to tinker, hi. Does that mean the volume's now too
> >>>>> low?--Matt, N1IBB.
> >>>>>
> >>>>> At 10:37 PM 7/18/2015 -0400, you wrote:
> >>>>>> Hi Matt,
> >>>>>>
> >>>>>> Been playing in the contest. I did see John responded to your other
> >>>>>> posts. He said the same thing I had mentioned, that you
> need to follow
> >>>>>> the instructions for what levels to set within Windows for the SL's
> >>>>>> sound card
> >>>>>>
> >>>>>> The "overflow" message means too much drive for the sound card. So
> >>>>>> you should lower the level on the RX drive knob.
> >>>>>>
> >>>>>> On a previous question:
> >>>>>>
> >>>>>> I don't think there is a hot key to get to the RX
> window. This is
> >>>>>> where you and your screen reader become fast friends.
> >>>>>>
> >>>>>> Don't worry. Next week you get to tackle PSK.
> >>>>>>
> >>>>>>
> >>>>>> If you smell smoke, pull the plug and run.
> >>>>>>
> >>>>>> 73, Steve KW3A
> >>>>>>
> >>>>>> On 7/18/2015 10:24 PM, Matthew Chao wrote:
> >>>>>>> Hi, Folks. Somehow, I messed up my MMTTY settings. When I run the
> >>>>>>> test files, I get overflow, and no text. Is the mic volume on my SL
> >>>>>>> USB too high? What happened? Thanks.--Matt, n1ibb.
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>
> >>>
> >>>
> >
> >
> >
|