Do you know what version? You might want to check eham.net, qth.com, and
sites like that, they often sell for less than that. I have one of those
here but I built it out of about 6 or 7 bad ones but don't use it for a
whole lot.
----- Original Message -----
From: "carolyn johnson" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Saturday, May 31, 2014 3:35 PM
Subject: Re: packet software
> It's a cam all mode. It was almost $400 brand new, so I should get that.
> It
> was hardly used. I don't remember the modle, but it does everything. Hope
> that helps.
>
> Carolyn Kj4vt
>
>
> --------------------------------------------------
> From: "John Miller" <[log in to unmask]>
> Sent: Saturday, May 31, 2014 2:16 PM
> To: <[log in to unmask]>
> Subject: Re: packet software
>
>> What make and model is it? Sorry to say I don't think for a used TNC,
>> you're
>> going to get anywhere near that for it.
>> ----- Original Message -----
>> From: "carolyn johnson" <[log in to unmask]>
>> To: <[log in to unmask]>
>> Sent: Saturday, May 31, 2014 11:01 AM
>> Subject: Re: packet software
>>
>>
>>> Hi,
>>>
>>> Speaking about packet, I still have an all mode packet unit that I'm
>>> trying
>>> to sell. It was hardly used, and is in its original box. I'd like $200
>>> plus
>>> shipping. I figure it should be around $25. I send everything through
>>> the
>>> postoffice, and even though they might be a little bit more, they are
>>> very
>>> helpful. I don't use paypal, but it's the last thing that I still want
>>> to
>>> get rid of. There isn't really any packet around here. Our repeaters
>>> have
>>> such good range being all the mountains around here. We used to use
>>> packet
>>> in Florida. We've been here almost three years, so the unit hasn't been
>>> used
>>> since then. I hate to see it just set, so anyone who is interested,
>>> please
>>> send me an email.
>>>
>>> [log in to unmask]
>>>
>>> Thanks,
>>>
>>> Carolyn Kj4vt
>>>
>>>
>>>
>>> --------------------------------------------------
>>> From: "John Miller" <[log in to unmask]>
>>> Sent: Saturday, May 31, 2014 5:39 AM
>>> To: <[log in to unmask]>
>>> Subject: Re: packet software
>>>
>>>> with windows that new, you're about limited to outpost which is a good
>>>> program, I hope the new version is still as god as the older ones were.
>>>> I
>>>> installed my version a few years ago and saw no reason to upgrade so
>>>> never
>>>> did but I know at lest up to version 2.6 is good with jaws. I'd doubt
>>>> if
>>>> you'll find a cable with usb on one end and db-25 on the other, I've
>>>> never
>>>> seen one, you'll have to get a USB to serial then a serial cable with
>>>> the
>>>> db-25 male on one end and db-9 female on the other which are still very
>>>> easy
>>>> to find last time I tried. I run the KPC-3 plus here and have for many
>>>> years
>>>> and even have a spare one, one of the few things I still have a backup
>>>> for
>>>> and mine runs 24-7. I have a desktop at the radio desk though which has
>>>> serial ports in it so for now don't need any serial to USB converters
>>>> on
>>>> that setup and hopefully enough XP machines to last a long time because
>>>> the
>>>> newer the version of windows the more difficult things become with
>>>> stuff
>>>> like that.
>>>> ----- Original Message -----
>>>> From: "DAN REID" <[log in to unmask]>
>>>> To: <[log in to unmask]>
>>>> Sent: Saturday, May 31, 2014 4:38 AM
>>>> Subject: packet software
>>>>
>>>>
>>>>> Help! searching for packet software for the kamtronics kpc-3+.
>>>>>
>>>>> I am using windows 7 and jaws version 15.
>>>>>
>>>>> Is there also a cable with a usb on one end and rs232 25 pin on the =
>>>>> other?
>>>>>
>>>>> thanks,=20
>>>>>
>>>>> dan
>>>>>
>>>>> kb6unc
|
