Hi Michael. Do you recall what frequency you heard me on, and about what
time? I participate with a couple groups on 40 each day, so perhaps you
heard me as part of one of my groups. Certainly I would have responded to
you if I had heard you.
73
Alan R. Downing
Phoenix, AZ
-----Original Message-----
From: For blind ham radio operators [mailto:[log in to unmask]]
On Behalf Of Michael Thurman
Sent: Tuesday, June 10, 2014 11:01 AM
To: [log in to unmask]
Subject: Re: Crimped Coax
ok cool :) oh and btw I heard you a while back on the air=85 rock =
crushing signal on 40 but you apparently did not hear me. I think it was =
just a random qso.
Michael Thurman
[log in to unmask]
On Jun 10, 2014, at 1:43 PM, Alan R. Downing <[log in to unmask]> wrote:
> Tessco's number is 800-472-7373. Give them a call and tell them that =
you
> are looking for an SMA barrel(male or female will have to be =
specified), and
> they will be happy to check.
> I have an account there, so I just email or call my sales rep =
directly, but
> you can always call in on their main 800 number.
>=20
> Alan/KD7GC
>=20
>=20
>=20
> Alan R. Downing
> Phoenix, AZ
>=20
>=20
> -----Original Message-----
> From: For blind ham radio operators =
[mailto:[log in to unmask]]
> On Behalf Of Michael Thurman
> Sent: Tuesday, June 10, 2014 10:25 AM
> To: [log in to unmask]
> Subject: Re: Crimped Coax
>=20
> do they have a double male SMA so I can use my upgraded rubber duck =3D
> that fits my former baofeng ht to work on my old yaesu? Probably cost =
=3D
> more than just a new antenna=3D20
>=20
> Michael Thurman
> [log in to unmask]
>=20
>=20
>=20
> On Jun 10, 2014, at 1:20 PM, Alan R. Downing <[log in to unmask]> wrote:
>=20
>> I buy almost all of my connectors from Tessco. Tessco carries a huge
>> selection of every kind of connector known to mankind.
>> =3D20
>> 73
>> =3D20
>> =3D20
>> Alan R. Downing
>> Phoenix, AZ
>> =3D20
>> =3D20
>> -----Original Message-----
>> From: For blind ham radio operators =3D
> [mailto:[log in to unmask]]
>> On Behalf Of John Miller
>> Sent: Tuesday, June 10, 2014 9:15 AM
>> To: [log in to unmask]
>> Subject: Re: Crimped Coax
>> =3D20
>> Radio shack has never had good crimp connectors, I dealt with a lot =
of =3D
> it in
>> =3D20
>> my CB days and none of it ever lasted especially on their pre made =3D
> cables.=3D20
>> IF you get decent quality crimp connectors or decent quality pre made =
=3D
> cables
>> =3D20
>> and stay far far from radio shack crap, it's every bit as good as a =3D=
> soldered
>> =3D20
>> connector no matter what anyone says.
>> ----- Original Message -----=3D20
>> From: "Steve" <[log in to unmask]>
>> To: <[log in to unmask]>
>> Sent: Tuesday, June 10, 2014 11:28 AM
>> Subject: Crimped Coax
>> =3D20
>> =3D20
>>> This is interesting. I remember when I put up my first tower. I =3D=
> was on=3D20
>>> a
>>> budget. I had good coax for my VHF antenna. Then, I picked up =3D
> 100-feet
>>> from Radio Shack for my junior tribander.
>>> =3D20
>>> The first or second day, I was working a JA on 20-meters. All of =
a=3D20=3D
>=20
>>> sudden,
>>> the signals dropped, and my SWR jumped. I went out and someone told =
=3D
> me it
>>> looked like the coax had come off of the tribander.
>>> =3D20
>>> I don't know if I had enough of a loop on it or what, but the =
damn=3D20
>>> crimp-on
>>> connector was living in the driven element and the coax was just =3D
> hanging
>>> there. Had to untape the cables, take that one down and resolder it =
=3D
> to a
>>> real connector and bring it up the next day.
>>> =3D20
>>> Now, I just feel uncomfortable using crimped coax. But, if that is =
=3D
> what=3D20
>>> LMR
>>> recommends, then I hope they have better crimp-on connectors.
>>> =3D20
>>> Steve, K8SP
>>> ----- Original Message -----=3D20
>>> From: "Alan R. Downing" <[log in to unmask]>
>>> To: <[log in to unmask]>
>>> Sent: Saturday, June 07, 2014 1:18 PM
>>> Subject: Re: West Mountain Crimping Tool and Coax?
>>> =3D20
>>> =3D20
>>>> Colin, none of the LMR series of coax are supposed to be soldered. =
=3D
> I buy
>>>> a
>>>> ton of connectors for LMR240, LMR400, LMR600, and LMR900, and not =
a=3D20=3D
>=20
>>>> single
>>>> one of them is soldered. Times Micro, the maker of LMR coax, wants =
=3D
> their
>>>> connectors to be crimped on. I own a whole bunch of special prep =3D=
> and
>>>> crimping tools specifically for the different sizes of LMR coax, =3D
> because
>>>> the
>>>> connectors have to be crimped.=3D20
|