John was right, it could go either way since it is 3 wires straight
across at each end and the middle ones open.
Just wondering, does the radio go into tx as soon as it is turned on and
the SL plugged in, or does it only go into tx when the software is started?
73, Steve KW3A
On 6/17/2013 4:19 PM, DAN REID wrote:
> just to be sure, I tried it both ways with the same results. =20
> thanks, kb6unc
> dan reid
> ----- Original Message -----=20
> From: Steve Forst<mailto:[log in to unmask]>=20
> To: =
> [log in to unmask]<mailto:[log in to unmask]>=20
> Sent: Monday, June 17, 2013 2:05 PM
> Subject: Re: signalink
>
>
> Are you sure the jumper block is installed right and that it is the=20
> right one? Some time ago I had a jumper for the 480 in backwards and =
>
> had the same result.
>
> If I remember right, you are going into a TS-2000. Are you going in =
> via=20
> the 13 pin din plug on the rear? Is everything plugged in correctly?
>
> 73, Steve KW3A
>
> On 6/17/2013 3:46 PM, DAN REID wrote:
> > It is putting out a steady carrier. =3D20
> > ----- Original Message -----=3D20
> > From: Steve =
> Forst<mailto:[log in to unmask]>=3D20<mailto:[log in to unmask]>
> > To: =3D
> > =
> [log in to unmask]<mailto:[log in to unmask]>=3D20<=
> mailto:[log in to unmask]:[log in to unmask]
> RG%3E=3D20>
> > Sent: Monday, June 17, 2013 1:43 PM
> > Subject: Re: signalink
> >
> >
> > Dan,
> >
> > Not familiar with all of this software, but what do you mean when =
> you=3D20
> > say "all I get is a straight carrier"?
> >
> > Is the rig going into TX and putting out a steady
> > carrier, or are you hearing a constant tone on RX?
> >
> > 73, Steve KW3A
> >
> > On 6/17/2013 3:34 PM, DAN REID wrote:
> > > digipan, echo link, ham radio deluxe, mixw, mmtty and with the =
> n3fjp =3D
> > =3D3D
> > > software.
> > > Same results for all of them. arrg!=3D3D20
> > > Dan (kb6unc)=3D3D20
> > > ----- Original Message -----=3D3D20
> > > From: Steve =3D
> > =
> Forst<mailto:[log in to unmask]>=3D3D20<mailto:[log in to unmask]<mailto:=
> [log in to unmask]:[log in to unmask]>>
> > > To: =3D3D
> > > =3D
> > =
> [log in to unmask]<mailto:[log in to unmask]>=3D3D2=
> 0<mailto:[log in to unmask]:[log in to unmask]
> .ORG%3E=3D3D20><=3D
> > =
> mailto:[log in to unmask]:[log in to unmask]
> <mailto:[log in to unmask]:[log in to unmask]
> O>=3D
> > RG%3E=3D3D20>
> > > Sent: Monday, June 17, 2013 5:45 AM
> > > Subject: Re: signalink
> > >
> > >
> > > What software are you using?
> > >
> > > 73, Steve KW3A
> > >
> > > On 6/16/2013 9:27 PM, DAN REID wrote:
> > > > Does anyone have any helpful hints as to how to get =
> activity =3D
> > through =3D3D
> > > the =3D3D3D
> > > > signalink? I've set both input and output to the usb =
> speakers =3D
> > and =3D3D
> > > mic, =3D3D3D
> > > > but all I get is a straight carrier. thanks,
> > > > dan (kb6unc)
> > > >
> > > >
> > > >
> > >
> > >
> > >
> >
> >
> >
>
>
>
|