which should I reset, VFO, etc> hmm! thanks! you're probably right,
and I do have the memories, etc. backed up on my computer.
At 09:12 AM 05/27/13, you wrote:
>I can't explain that one; I've heard that pause on every Kenwood I have with
>that feature. Granted, it's a very short pause, maybe a tenth of a second,
>but it's there on all my radios. May be time for a reset.
>
>Steve
>
>----- Original Message -----
>From: "Curtis Delzer" <[log in to unmask]>
>To: <[log in to unmask]>
>Sent: Monday, May 27, 2013 03:36
>Subject: Re: tmv-71
>
>
> > that is the point, I am not hearing that "pause" or any audible of
> > anything happening, only the high error beep when I hold the reverse
> > button for longer than a second.
> >
> >
> > At 09:35 AM 05/26/13, you wrote:
> >>Curtis,
> >>
> >>The only audible thing you'll hear is a momentary pause while the radio
> >>checks the input. I don't think you'll actually hear any audio present on
> >>the input (at least, I never have).
> >>
> >>Steve
> >>
> >>----- Original Message -----
> >>From: "Curtis Delzer" <[log in to unmask]>
> >>To: <[log in to unmask]>
> >>Sent: Sunday, May 26, 2013 02:10
> >>Subject: Re: tmv-71
> >>
> >>
> >> > pressing "rev" is the "reverse key," which then=20
> >> > monitors the input of the repeater. holding down=20
> >> > the "rev" or reverse key is suppose to turn on=20
> >> > the automatic frequency checker, and also then,=20
> >> > every 3 seconds, the transceiver actually goes=20
> >> > into the reverse mode automatically listening to=20
> >> > the input of the repeater.. the icon blinking=20
> >> > means it hears something on the input, but I just=20
> >> > cannot get it to do something audibly, though I=20
> >> > think I did hear it work, once. meaning it was=20
> >> > turned on once, but I never got it to do it again. :)
> >> >
> >> >
> >> > At 07:29 PM 05/25/13, you wrote:
> >> >> The automatic frequency checker sounds like a visual thing.
> >> >>
> >> >> >From the manual
> >> >>
> >> >>Press [REV] (1s) to turn the ASC ON.
> >> >>
> >> >>When the ASC is ON, the icon will appear on the display.
> >> >>
> >> >>=B7 While direct contact is possible, without the use of a repeater,
> >> >>the=
> >> > icon
> >> >>will
> >> >>
> >> >>begin blinking.
> >> >>
> >> >>=B7 To exit ASC, press [REV].
> >> >>
> >> >>Note:
> >> >>
> >> >>Pressing [PTT] will cause the icon to stop blinking.
> >> >>
> >> >>ASC does not function if you are using simplex operation.
> >> >>
> >> >>ASC does not function while scanning.
> >> >>
> >> >>Activating ASC while using Reverse will switch the Reverse function
> >> >>OFF.
> >> >>
> >> >>If you recall a Memory channel or the Call channel, and those channels
> >> >>are
> >> >>set
> >> >>
> >> >>up with the
> >> >>
> >> >>Reverse function switched ON, the ASC will switch OFF.
> >> >>
> >> >>A
> >> >>
> >> >>
> >> >>
> >> >>
> >> >>
> >> >>display and blinks. Press any key other than the Tuning control while
> >> >>the
> >> >>
> >> >>I wonder what "press "rev" means, I think they are talking about menu=
> >> > setup,
> >> >>but am not sure about the manual's translation, or my understanding.
> >> >
> >
|