Perhaps there is a menu item where the voice guidance speed can be adjusted
in the '450. I'm not sure.
I have written several times before about using the FT950. I have had it
for nearly 5 years now, and still think I made the right decision in buying
it. If I were starting out right now, I would take a hard look at the
TS590, but I don't see a need to switch to that rig from what I currently
use. The FT950 has enough knobs and switches to satisfy most hams. The
keypad can be used either to select one of the three "band stack" memories
for each ham band or to enter frequencies. Beeps indicate when buttons have
been pushed, whether an erroneous entry was made or the SWR is too high, and
when a secondary function has been activated. There are real knobs for
adjusting squelch, mike gain, monitor level, CW speed, and RF and AF gain.
Several different tuning rates are available, and on A M it can be tuned in
5 or 50 KHz increments if you wish, using the detented Select knob.
Sometimes I really want to know what frequency I have tuned to. You can
accurately estimate, based on the current mode and tuning rate, or read with
N1MM or Ham Radio Deluxe's "voice synthesizer" option.
I have looked at the manuals for the FTDX3000 and 5000, and am not sure how
you would get to a particular menu number. There may be a way, and I have
never had my hands on those rigs. It may seem tedious and unnecessary, but
I can reach any of the 118 menu items by counting clicks.
Anyway, I'm only saying that the FT950 gives me enough accessibility to get
by, and is a good value. No rig is right for everybody.
73, W3IUU
-----Original Message-----
From: Kelvin Marsh
Sent: Monday, December 31, 2012 4:00 PM
To: [log in to unmask]
Subject: Re: accessiblity of two yaesu radios
Hi,
I've recently had an FT-450 on the bench here, to write an accessibility
review for Active Elements. One of the big charities in the UK has bought
FT-450s for their blind members, and I was keen to take a look.
In my opinion, the fact it has a voice readout fitted as standard is fairly
misleading. The uninitiated will believe it is accessible.
I found the frequency readout did not read to the hundreds of kilohertz. It
would read 7.100.0. It was missing the last digit you need for standard
accuracy. OK, you could net with a station by ear, but you could never get
to 7.100.00 to run an exact rounded frequency yourself. There was no
keypad, compounding the problem.
The second niggle was that pressing the readout key, caused the RX to be
silent. The voice was so slow, it took 13 seconds to read.
I only evaluated the FT-450, not the FT-450D. Perhaps it has improved...
In contrast, I've also just had a few days with a FT-2000. OK, there is no
voice chip, but I could use this fairly happily through the CAT, including
using split and the second RX.
Best wishes, Kelvin Marsh - M0AID
Working to improve accessibility for radio amateurs with disabilities
www.active-elements.org
For accessibility evaluations of amateur equipment and MP3 manuals
-----Original Message-----
From: For blind ham radio operators [mailto:[log in to unmask]]
On Behalf Of John Miller
Sent: 31 December 2012 18:08
To: [log in to unmask]
Subject: Re: accessiblity of two yaesu radios
Yaesu never did care about accessibility, the 847 was a 1 off try at it and
had a lot of problems, and now they have the ft-450 which took one of my
sighted friends, with the manual almost 3 hours to figure out how to turn
the voice read out on at a special event so I could use the radio and I
still did not like the radio at all. The RIT/XIT knob on my ts-2000 is about
the size of the tuning dial on the FT-450, even the IC-706 has a bigger dial
than that. I was far from impressed. Sadly that's what a lot of the hospital
EOC's have in this area of the state, I suppose if you're not tuning around
it's OK, but I'd hate to have to sit there tuning around with it.
----- Original Message -----
From: "Michael Thurman" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Monday, December 31, 2012 11:55 AM
Subject: Re: accessiblity of two yaesu radios
> yaesu walked away from accessible radios when they dropped the ft 847 =
> which is why I will not own another yaesu rig. also icon and ken wood =
> rigs seem to be more reliable in my opinion
> On Dec 30, 2012, at 1:29 PM, Bob Ray <[log in to unmask]> wrote:
>
>> Greetings, I already know about the wonders of the kenwood products =
> like
>> the TMV-71A but I have been asked if a person can use either the =
> FT-8900R or
>> VR-7R(b)? Any thoughts on these two radios would be appreciated.
>>=20
>> 73,
>>=20
>> Bob KD0BR
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2013.0.2805 / Virus Database: 2637/5981 - Release Date: 12/23/12
Internal Virus Database is out of date.
|