Quite so, Mike. I should've been more specific there. All the settings on
the K3 have relative numbers assigned to them, much as an analog knob or
dial might point to a number on a relative scale. As Mike said, what you
can't do yet is read the ALC indication on the bar graph which is The
digital equivalent to the VU or ALC meter.
Lou Kolb
Voice-over Artist:
Radio/TV Ads, Video narrations
Messages On-hold:
www.loukolb.com
----- Original Message -----
From: "Mike Cozzolino" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Thursday, August 23, 2012 12:56 PM
Subject: Re: Accessible Transceivers
> hello lou, you can tell where the compressor and mic gain are set
> with the ham pod but you are correct the alc is not accessible yet
> through the serial port. i have my processor set at 22 and my mic
> gain set at 17 and once you know where the gains need to be set you
> really don't need the alc info. and jim the radio does talk the info
> on the display, so if you are in rtty and you get a signal tuned in
> the speech speaks the words that are going across the display. the
> adjustment is very critical which is the firmware in the radio not
> the hampod. the hampod just reports what is on the display. i have
> the hampod here also and was the first to have one because i worked
> with rob to get it going. guess you could say i was his ginni pig
> smile.also what you should all know is that the hampod was not
> designed only for the k3, but it will eventually be made to read the
> info that is available on any radio that outputs the data to the
> serial port. he will have to get his hands on each radio and modify
> the hampods firmware to work on that radio. the hampod also has two
> inputs one for the radio and the other can be used to make your rotor
> talk or a wattmeter or any accessory that has a serial port and
> outputs the info to it. so a hampod is really just beginning and
> will evolve into a great accessibility device. guess that is all i
> can think of to tell you but lookout the hampod is here. take care,
> c u 73 mike w6quv
>
>
>
> At 03:01 AM 8/23/2012, you wrote:
>>Jim,
>>
>>The Hampod has a doubletalk synth so everything it says is in that voice.
>>It does give excellent access to the K3 display and to the menus and I can
>>attest that everything Armand says about Rob and his service are
>>absolutely
>>true.
>>
>>In the interest of accuracy, though, I should point out that there is one
>>thing we can't do with the hampod yet and that is setting audio input
>>levels. This is not a hampod issue but rather a K3 issue. That info just
>>isn't available to the serial port yet. I know Rob has been in contact
>>with
>>Elecraft about it and hopefully it will be fixed soon. There is no doubt
>>though that the K3 performance and the hampod access makes an extremely
>>powerful package.
>>Lou Kolb
>>Voice-over Artist:
>>Radio/TV Ads, Video narrations
>>Messages On-hold:
>>www.loukolb.com
>>----- Original Message -----
>>From: "Jim Gammon" <[log in to unmask]>
>>To: <[log in to unmask]>
>>Sent: Thursday, August 23, 2012 4:22 AM
>>Subject: Re: Accessible Transceivers
>>
>>
>> > Hi Armand, man that Elecraft sounds terrific! The the hampod give
>> > you voice or CW output? I thought it was CW only, but you make it
>> > sound like the things speaks everything including when your
>> > dinner's ready and when you should do your laundry etc. Heck, I
>> > graduated from a Drake Tr-4c to a Kenwood Ts-480 with speech so I
>> > think that's the cat's meow. Guess you'll have to bring the
>> > Elecraft to an a's game where we can meet up so I can check it
>> > out. Smile! y73, Jim WA6EKS
|