Curt,

Sorry about the slow response.  The buttons for memory are in the third row 
down from the bottom of the display, and they are to the right of the tuning 
knob.  The button on the left toggles between memory and VFO; the next 
button is for entering things into memories; and the third button is for 
writing the contents of a memory to the VFO (either A or B, depending on 
what you've selected with the A/B button).

To write to a memory:

1.  Enter the frequency, split info,  mode, and PL tone if applicable into 
the VFO.
2.  Press the second button from the left in the third row down (as 
described above).  The radio will announce the contents of the memory or 
"blank" if nothing has been entered.
3.  Rotate the Channel knob to select the desired memory.
4.  Press the second button again.  A long beep indicates that the contents 
of the VFO have been stored in memory.

Steve

----- Original Message ----- 
From: "Curtis Delzer" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Friday, October 21, 2011 23:26
Subject: Re: Fun on 10 meters


> how to enter into memory? that is my next question to you, Steve. :) 
> thanks!
>
>
> At 05:49 PM 10/17/2011, you wrote:
>>     Thanks, Kevin.
>>
>>This helps a lot.
>>
>>I'll put 10 meter repeaters on my list as something else to try in the
>>months ahead, assuming that 10 meters stays open.
>>
>>73 from Tom Behler:  KB8TYJ
>>
>>----- Original Message -----
>>From: "Kevin Nathan" <[log in to unmask]>
>>To: <[log in to unmask]>
>>Sent: Monday, October 17, 2011 9:12 AM
>>Subject: Re: Fun on 10 meters
>>
>>
>> > Hi Tom,
>> >
>> > The standard offset is 100 kHz and no, the 590 does not automatically 
>> > put
>> > in
>> > this split.  I set up repeaters in memories using split channels.  The
>> > receive frequencies for the repeaters are 29.620, 29.640, 29.660 and
>> > 29.680.
>> > Your transmit frequency should be 100 kHz lower and using a tone of 
>> > 88.5.
>> > The FM simplex frequency is 29.600 with no tone of course.
>> >
>> > I hope this helps and very 73.
>> >
>> >
>> >
>> > Kevin :)
>> > Amateur Radio:  K7RX
>> >
>> >
>> > -----Original Message-----
>> > From: For blind ham radio operators 
>> > [mailto:[log in to unmask]]
>> > On Behalf Of Tom Behler
>> > Sent: Monday, October 17, 2011 02:26
>> > To: [log in to unmask]
>> > Subject: Re: Fun on 10 meters
>> >
>> >    Kevin:
>> >
>> > You guys are now getting me interested in trying a 10-meter repeater
>> > contact
>> >
>> > myself when band conditions allow.
>> >
>> > I have two questions, and hopefully, others will benefit from whatever
>> > answers I get:
>> >
>> > 1.  What is the standard off-set for 10 meter repeaters?
>> >
>> > and
>> >
>> > 2.  Does the TS590 automatically enter those off-sets when you program 
>> > a
>> > 10-meter repeater into the rig, or must that be done manually?
>> >
>> > Thanks, and 73 from Tom Behler:  KB8TYJ
>> >
>> > ----- Original Message -----
>> > From: "Kevin Nathan" <[log in to unmask]>
>> > To: <[log in to unmask]>
>> > Sent: Sunday, October 16, 2011 10:57 PM
>> > Subject: Re: Fun on 10 meters
>> >
>> >
>> >> Hi Steve,
>> >>
>> >> To go back to ten meters a minute, I got up there this afternoon after
>> >> reading your message.  I worked two stations through that repeater on
>> >> 29.660
>> >> in Dallas/Fort Worth and had a ball.  They were my first actual 
>> >> repeater
>> >> contacts on ten meters.  One was a mobile in Vermont and the other was 
>> >> a
>> >> guy
>> >> in Forth Worth on the 440 side talking to me on ten.  Worked some DX 
>> >> on
>> >> SSB
>> >> as well and all in all, had a great time.  Thanks for the tip.
>> >>
>> >> Take care and very 73.
>> >>
>> >>
>> >>
>> >> Kevin :)
>> >> Amateur Radio:  K7RX
>> >>
>> >>
>> >> -----Original Message-----
>> >> From: For blind ham radio operators
>> >> [mailto:[log in to unmask]]
>> >> On Behalf Of Steve Forst
>> >> Sent: Sunday, October 16, 2011 19:45
>> >> To: [log in to unmask]
>> >> Subject: Re: Fun on 10 meters
>> >>
>> >> Howard,
>> >>
>> >> For RTTY I use the free MMTTY software:
>> >>
>> >> http://hamsoft.ca/pages/mmtty.php
>> >>
>> >> As you would expect, tuning in the signal, and getting your screen
>> >> reader to spit out something understandable is the hardest part.   Do 
>> >> a
>> >> simple audio connection from radio to pc sound card and play around.
>> >> Once you get the rx side working, than you can decide on how you want 
>> >> to
>> >> tx.
>> >>
>> >> With JAWS, I found that putting a frame around the rx window and
>> >> setting it up to read incoming text works pretty well.   Otherwise use
>> >> insert-s to "all" to read incoming text.
>> >>
>> >> Good luck, Steve KW3A
>> >>
>> >
>