you are correct I just wanted to make sure you remembered.
----- Original Message -----
From: "Tom Behler" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Saturday, September 10, 2011 11:08 AM
Subject: Re: one more little problem
> John:
>
> I believe the wave files are enabled when you check voice navigation for
> all
> fields. At least that was my experience with Windows XP whenever I
> installed the N3FJP software.
>
> 73 de KB8TYJ
>
> ----- Original Message -----
> From: "John Miller" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Saturday, September 10, 2011 10:09 AM
> Subject: Re: one more little problem
>
>
>> You do have to enable the wav files in the program, I'd have to do it to
>> remember where to go but you do have to go in to options somewhere to
>> enable
>> them.
>> ----- Original Message -----
>> From: "Steve Forst" <[log in to unmask]>
>> To: <[log in to unmask]>
>> Sent: Saturday, September 10, 2011 9:40 AM
>> Subject: Re: one more little problem
>>
>>
>>> Tom,
>>>
>>> I don't use the N3FJP stuff, although I do use some of Kimberly's .wav
>>> files in Writelog. Since I've been loaded with suggestions this week,
>>> here is another one:
>>>
>>> Assuming the location and format of the .wav files is correct, perhaps
>>> it goes back to the sound card issue. There may be a menu setting or
>>> configuration .ini file where you can see what sound device N3FJP is
>>> looking for to play the .wav audio.
>>>
>>> If you connect the radio to the pc with your usb/serial thingy(no
>>> changes in any radio menus needed, just tell N3FJP the new port number)
>>> and unplug the usb cable, see if the wave files play.
>>> There could be any number of things going on here, but finding out what
>>> sound card the software is trying to use may be a good idea. You may
>>> need to tell it which device to use.
>>>
>>>
>>>
>>> On moving the window in the Kenwood software: You can drag it with a
>>> mouse, or from the keyboard alt-spacebar should bring up a menu
>>> with"move" as an item. Hit enter and use the arrow keys to move the
>>> window and then *I think* hit enter again to get out.
>>>
>>> 73, Steve KW3A
>>>
>>> On 9/10/2011 6:43 AM, Tom Behler wrote:
>>>> Hi, again folks.
>>>>
>>>> I have another issue to tap into everyone's wisdom about, but I'm going
>>>> to
>>>> put this one in the category of a small nuisance-type issue. It
>>>> regards
>>>> the
>>>> N3FJP logging software, and is probably another Windows 7 issue, since
>>>> I
>>>> never experienced anything like this with Windows XP.
>>>>
>>>> Specifically, I have successfully installed the NAQP 2.4 software onto
>>>> my
>>>> new Windows 7
>>>> laptop. I also have managed to get the CW keying and the rig interface
>>>> working with the NAQP software.
>>>>
>>>> My only issue is this: I can't seem to get Kimberlee's wave files to
>>>> play.
>>>> I have downloaded and copied the wave files into the Program files
>>>> folder
>>>> for the NAQP 2.4 software, and have gone into "options" and checked all
>>>> voice navigation fields. However, this doesn't seem to have helped.
>>>> Do I need to turn something on in Windows 7 in order to hear these wave
>>>> files? If so, how do I do this?
>>>>
>>>> Might I do better to install something like Winamp for this purpose
>>>> rather
>>>> than messing with Windows Media Player, and if so, how can I make
>>>> Winamp
>>>> my
>>>> default player?
>>>>
>>>> As always, everyone's help is very much appreciated!
>>>>
>>>> Vy 73 from Tom Behler: KB8TYJ
>>>>
>>>>
>>>>
>>
|
