Yup, got it, Jerry.

Will definitely give it a try a little later.

73 de KB8TYJ

----- Original Message ----- 
From: "Gerry Leary" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Tuesday, December 20, 2011 8:18 PM
Subject: Re: WhiteStick Log Question


> you have to add a g on the end of the file extension.
> ----- Original Message ----- 
> From: "Tom Behler" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Tuesday, December 20, 2011 5:03 AM
> Subject: Re: WhiteStick Log Question
>
>
>>    Howard:
>>
>> Maybe I'm making this harder than it needs to be.
>>
>> Once I do the editing, will the program file just work with the software
>> as
>> is, when I launch it?
>>
>> If so, sorry about my last two posts.
>>
>> Guess it's good that I'm not trying to be a computer programmer as a way
>> to
>> make  a living!  (grin)
>>
>> 73 from Tom Behler: Kb8TYJ
>>
>> ----- Original Message ----- 
>> From: "Howard, W A 9 Y B W" <[log in to unmask]>
>> To: <[log in to unmask]>
>> Sent: Monday, December 19, 2011 11:15 PM
>> Subject: Re: WhiteStick Log Question
>>
>>
>>> Tom,
>>>
>>> I didn't read all the way down in your e-mail.  It looks like you 
>>> already
>>> found what to do.  You will need to edit that first line in the
>>> Kenwood.rig
>>> file using a text editor.  Do not use Word or Wordpad, must be something
>>> like NotePad.
>>>
>>> Exactly what is it you are trying to do?
>>>
>>> Howard #3
>>>
>>> ----- Original Message ----- 
>>> From: "Tom Behler" <[log in to unmask]>
>>> To: <[log in to unmask]>
>>> Sent: Monday, December 19, 2011 9:18 PM
>>> Subject: WhiteStick Log Question
>>>
>>>
>>>> Hi, folks.
>>>>
>>>> Well, I believe I successfully installed WhiteStick log on my Windows 7
>>>> laptop.
>>>>
>>>> I didn't think it would work, but the program seems to be there. It
>>>> seems
>>>> to
>>>> function well, and is extremely Jaws friendly.
>>>>
>>>> So, thanks to Howard number 3 for posting the link.
>>>>
>>>> I do have one question, though.
>>>>
>>>> Where do you find the Cat Rig Control set-up in the software?
>>>>
>>>> It is clear from the text below in the Instructions folder that you can
>>>> configure the software to work with your rig, but I can't find where to
>>>> go
>>>> to configure things.
>>>>
>>>> Here are the instructions.  Can anyone help?:
>>>>
>>>> CAT RIG CONTROL.
>>>> CAT rig control will be provided if you change the extension of one of
>>>> the
>>>> .RI files
>>>> provided to .RIG
>>>> It is important that only one of these files has the extension .RIG
>>>> When you change frequency or mode on the rig WSLog will update the
>>>> computer.
>>>> FT990 users must have revision one point three firmware or higher to
>>>> function correctly.
>>>> You may amend line one in the rig file; the first number is the COM
>>>> port,
>>>> followed by the baud rate, parity (N), number of data bits and number 
>>>> of
>>>> stop bits.
>>>> Alter these if they are not the rig defaults.
>>>> The com port number must be followed by a colon.
>>>> A general purpose ICOM rig file is provided, users will need to change
>>>> the
>>>> digits
>>>> marked xx to the address of the rig as supplied in the rig manual. 
>>>> These
>>>> values
>>>> are hexadecimal, only use the two digits, ignore the H.
>>>> A KENWOOD file provides for all Kenwood rigs.
>>>> Users of Yaesu FT817, FT847, FT857 and FT897 should use the FT8x7 file.
>>>> Users of Yaesu FT450, FT950, FT2000 and FTDX9000 should use the YAESU1
>>>> file.
>>>> CAT control is also provided for the TEN-TEC Pegasus rig.
>>>> The RIG file for that contains one line for the drive and path of the
>>>> Pegasus software.
>>>> This is typically C:\PEGASUS\ and the last character MUST be a back
>>>> slash.
>>>>
>>>> 73 from Tom Behler: KB8TYJ
>>>
>