Gary,
To change the offset direction, press Function followed by Reverse. The
first time you do this, you'll hear a low beep. Repeat the key sequence
again, and you'll hear a high beep. The offset will now be set to +. Note
that the Automatic Shift works only on 2 meters. On 440, you have to change
the direction manually.
Steve
----- Original Message -----
From: "Gary Smith" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Sunday, June 01, 2008 20:22
Subject: Re: TMV71A Question
> Hi Steve,
> I don't know what I did different but I finally got 444.150 MHZ stored in
> VFO B in channel 0. The problem now is that I need to change the offset
> direction to plus 5 MHZ instead of minus. How do you get it to change?
> Thanks, Gary
>
>
> -----Original Message-----
> From: For blind ham radio operators [mailto:[log in to unmask]]
> On Behalf Of Steve Dresser
> Sent: Sunday, June 01, 2008 7:13 PM
> To: [log in to unmask]
> Subject: Re: TMV71A Question
>
> Gary,
>
> What frequency are you trying to save, and which receiver are you using?
> This isn't an issue if the frequency is within the ham bands, but if not,
> there are frequencies which will only work with one or the other radio.
> For
>
> example, if you want to store a frequency between 118 and 136 MHz, you
> have
> to use the A radio.
>
> Steve
>
> ----- Original Message -----
> From: "Gary Smith" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Sunday, June 01, 2008 14:38
> Subject: Re: TMV71A Question
>
>
>> Hi Steve,
>> I did exactly what you described and instead of hearing the long beep it
>> was
>> a shorter high pitch beep and the frequency wasn't changed. Any
>> suggestions?
>>
>> Gary
>>
>> -----Original Message-----
>> From: For blind ham radio operators
>> [mailto:[log in to unmask]]
>> On Behalf Of Steve Dresser
>> Sent: Sunday, June 01, 2008 11:47 AM
>> To: [log in to unmask]
>> Subject: Re: TMV71A Question
>>
>> Gary,
>>
>> You don't have to delete the information in a memory to reprogram it.
>> Before entering the new frequency information, press Memory to get into
>> Memory Mode and turn the tuning knob until you hear the memory you want
>> to
>> change. Then, press VFO and begin entering the frequency and other
>> information you want to store in memory. Once you've entered the
>> information, press Function followed by Memory. You'll hear a long beep,
>> and the memory will be reprogrammed. You'll have to press Memory again
>> to
>> see the results of what you've done.
>>
>> Steve
>>
>> ----- Original Message -----
>> From: "Gary Smith" <[log in to unmask]>
>> To: <[log in to unmask]>
>> Sent: Sunday, June 01, 2008 11:54
>> Subject: TMV71A Question
>>
>>
>>> Hello TMV71A users,
>>>
>>> I finally got mine in and I'm trying to program the channels. I don't
>>> seem
>>> to have a problem when I enter frequencies in a blank channel but when I
>>> try
>>> to overwrite a frequency that is already in a channel it doesn't seem to
>>> work. Is there a different way to program those channels or do I need
>>> to
>>> delete what is in the channel first? If so, how do you delete what is
>>> already in a channel? Also, when I go to find a blank channel to put a
>>> frequency in it says memory in, channel low, 1 blank and the next click
>>> of
>>> the dial says memory in, channel up, 1 blank. What does low and up
>>> mean?
>>> I
>>> would appreciate any help. Feel free to email off list if you want.
>>>
>>>
>>>
>>> Gary, N5GD
>>>
>>> [log in to unmask]
>>>
>>>
>>>
>>
>>
>>
>
>
>
|