Hi Russ & Others
Have you tried different version of motherboard drivers. I have seen this
with VIA chips on the motherboard. I would start with the newest version of
VIA 4 in 1 driver until I found a winner. If that does not work I ran into
a motherboard with VIA chip also that needed the ACPI turned off. To do
this, I needed to turn it off in the OS and then off in CMOS bootup. It
maybe worth a try.
Good Luck
Richard F. Bolha
> [Original Message]
> From: Russ Cox <[log in to unmask]>
> To: <[log in to unmask]>
> Date: 6/26/2006 4:26:14 PM
> Subject: Re: [PCBUILD] HP 8870 now Freezes on Boot up
>
> I believe my HP 7955 is dead after going thru some similar experiences
> as you have. Since it won't boot into anything, I can't continue to try
> to find out what really caused the freezes in the first place. So all I
> have now are theories. What do you think about these possible causes?
> 1. Power supply drop outs - since it would freeze at different stages of
> startup, could there be momentary drops in one or more of the PS
> voltages? The PS tests ok now, but maybe under load it drops out
> occasionally.
> 2. Some driver conflict - maybe since I can't really tell what drivers
> load when during boot. But the fatal failure was during flashing the
> BIOS from a bootable floppy when there aren't many drivers loaded.
> 3. Some firmware failure in the BIOS chip - Seems like it might be a
> possibility, but don't see why that could cause a freeze when the
> desktop was loaded.
> 4. Some other hardware failure on the motherboard - I just don't have a
> clue about which part or function this might be.
> I did chat with a tech at HP and his best conclusion was to replace the
> Power Supply and/or motherboard. That's moot now since I can't get the
> computer to boot into anything, and a new motherboard is not cost
> justified. And the Power Supply tests good when connected to a tester.
> I too have spent a ridiculous amount of time on the HP. I hope you are
> successful in finding and correcting the problem.
> Todd Schroeder wrote:
> > **UPDATE**
> >
> > Thank you both for your responses. I know if I take the computer in I
to
> > o will possibly be told something along the lines of "its a fried
motherb
> > oard" or "a corrupted hard-drive", and will have to pay 55 bucks an
hour
> > for it.
> >
> > I've spent a ridiculous amount of time working on it, more than any
avera
> > ge person would, but I believe I can get it back up and working. All
I'v
> > e been doing is disconnecting and reconnecting all the ribbons and
power
> > supply connectors that I had to take out when I put in the new card
becau
> > se they were in the way.
> >
> > Occasionally, (very occasionally sometimes w/o doing anything but
restar
> > ting)the computer will either boot up in BIOS or it will give me a
messag
> > e apoligizing, saying the computer detected that it was improperly
shutdo
> > wn, or that there were hardware changes. On the later it will begin to
c
> > ountdown from 30, giving me the option to start up in safe mode, or the
"
> > last configuration that knowingly worked".
> >
> > At one point I had selected "Last configuration that knowingly worked"
an
> > d the computer started up and worked just fine. This was with my
initial
> > TNT2 Pro card. Now, understand, when this worked, it had been my
first
> > time unplugging the ribbon that goes into the harddrive, and I thought
gr
> > eat, the NX6600 probably works fine. However, before I shut down, I
unin
> > stalled the drivers for the TNT2 Pro thinking that they may have been
cau
> > sing a hang-up.
> >
> > Put the NX6600 back in, back to freezing on "HP Invent" screen. Tried
un
> > plugging the ribbon, no luck. The closest I could get was a black
screen
> > with a blinking input. .... Cursed myself up and down here for being
a
> > moron for not just keeping the original AGP card in....and then went
bac
> > k to installing it back in. As of now I've got the original card back
i
> > n, but have not yet been able to get the "last configuration that
knowing
> > ly worked" screen to come up, without freezing (happened once).
> >
> > Its very frustrating, not sure whats wrong but the best I can conclude
is
> > that its a 5 year old computer and is having some kind of trouble
during
> > boot with this hardware change.
> >
> > Only thing I wondered is that in the BIOS theres an option to reset
confi
> > guration. I'm not planning to select "Yes" because I got it to work
befo
> > re w/o doing so, but was curious to know when you would use that.
> >
> > PCBUILD maintains hundreds of useful files for download
> > visit our download web page at:
> > http://freepctech.com/downloads.shtml
> >
> >
> >
>
> PCBUILD maintains hundreds of useful files for download
> visit our download web page at:
> http://freepctech.com/downloads.shtml
>
PCBUILD's List Owners:
Bob Wright<[log in to unmask]>
Drew Dunn<[log in to unmask]>
|