try coherent english next time and we might be able to assist you.
73
Colin, V A6BKX
----- Original Message -----
From: "Anthony Slate" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Tuesday, December 26, 2006 6:36 PM
Subject: Re: Which HT would _you_ select?
> How can I stop getting Blind ham email wher I fna read on line if I
descide
> to
>
> -----Original Message-----
> From: For blind ham radio operators [mailto:[log in to unmask]]
> On Behalf Of Kenneth Lee
> Sent: Tuesday, December 26, 2006 8:33 PM
> To: [log in to unmask]
> Subject: Re: Which HT would _you_ select?
>
> Colin, I should have explained myself better when I talked about using
split
> mode on the T90. I often setup my V7 in "half" cross-band repeater mode
so
> that the v7 listens on uhf and re-transmits on vhf, but it does not
> re-transmit the vhf side. I usually prefer this technique around the
house
> because I can hear the vhf repeater just fine on the HT but want to use
the
> extra power from the v7 to hit the repeater full quieting. In this half
> duplex mode the ht is simply a long range wireless microphone that can
also
> listen to the vhf side of the conversation. I don't usually use full
> cross-band repeat because the v7 gets really hot since it has to
re-transmit
> both sides of the conversation in this mode.
>
> 73, Ken -N5SWR
>
>
>
> -----Original Message-----
> From: For blind ham radio operators [mailto:[log in to unmask]]
> On Behalf Of Colin McDonald
> Sent: Tuesday, December 26, 2006 4:29 AM
> To: [log in to unmask]
> Subject: Re: Which HT would _you_ select?
>
>
> well, a cross band repeater is just that, a cross band repeater.
> You don't need to set up a split channel on the HT to use one, since the
> repeater is transmitting on one frequency, and listening on the same
> frequency. You only have to listen and transmit on one frequency from the
> handheld or mobile going through the cross band repeater.
> Lock band repeaters will only transmit from one band to the other, not
> listen, which means you would have to set up split on the HT to transmit
or
> listen on the freq you want.
> with the ts2000, and other cross banders, you set up the radio with a vhf,
> and a UHF freq, or an HF/vhf, or HF/UHF freq similtaniously, then turn on
> the cross band repeat function, and set your HT to the UHF or VHF freq you
> selected on the 2000, then when you transmit on the HT it will be received
> on the 2000, and retransmitted on the other frequency you previously set
up,
> then when the radio receives something on that other frequency, it will
> transmit it back to the original frequency on the HT.
> For instance, I cross band from 446.050 to 146.52 on the ts2000. I then
set
> my ICt90 to 446.050 simplex and I can transmit from the HT, which will be
> received by the 2000, retransmitted on 146.52. Then, when someone talks
on
> 146.52, the 2000 will retransmit that signal onto 446.050. So, no split
is
> required on the HT itself, just on the cross band radio.
> 73
> Colin, V A6BKX
>
> __________ NOD32 1939 (20061226) Information __________
>
> This message was checked by NOD32 antivirus system.
> http://www.eset.com
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.5.432 / Virus Database: 268.15.28/604 - Release Date:
12/26/2006 12:23 PM
>
>
|
