I am aware of this and rarely reuse connecters anyway. I suppose N
CONNECTORS DUE TO THE COST MIGHT BE WORTH TRYING TO RECYCLE BUT I HAVE
NOT USED THEM THOUGH I HAVE ABOUT A DOZEN SILVER PLATED IN MY PARTS
COLLECTION.
-----
BRETT WINCHESTER
[log in to unmask]
208-639-8386
###
-----Original Message-----
From: For blind ham radio operators
[mailto:[log in to unmask]] On Behalf Of Colin McDonald
Sent: Monday, February 12, 2007 3:24 PM
To: [log in to unmask]
Subject: Re: sealing outdoor coax connections
that would probably work as well, as long as the heat shrink tubing was
adequitly and evenly sealed. You can buy heat shrink tubing that has a
sticky sealant on the inside surface which works pretty well.
As long as just the coax, and the place where the coax enters the
connecter are treated with heat shrink, you can make a pretty
professional looking installation.
But if it is used for sealing a pl259 to an so239, or a pair of N
connecters, you'll not be able to use those connecters ever again...just
cut em off and resolder new ones if the antenna ever comes down.
73
Colin, V A6BKX
----- Original Message -----
From: "Brett Winches" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Monday, February 12, 2007 11:46 AM
Subject: Re: sealing outdoor coax connections
> What about using heat shrink and than the tape? =20
>
>
> =20
>
> -----
>
> BRETT WINCHESTER
>
> [log in to unmask]
>
> 208-639-8386
>
> ###
>
> =20
>
> =20
>
>
> -----Original Message-----
> From: For blind ham radio operators
> [mailto:[log in to unmask]] On Behalf Of Colin McDonald
> Sent: Sunday, February 11, 2007 11:47 AM
> To: [log in to unmask]
> Subject: Re: sealing outdoor coax connections
>
> Tom:
> You have already gotten most of the information you'll need, but as
per
> normal, I will put my quarters worth in anyway.
> As was said, put the sealer tape on first to give the connection a
good
> solid water tight seal. If the electrical tape goes on first, as john
> mentioned, any gaps or spaces left by the tape will potentially gather
> moisture, dirt, dust or what ever else might happen by.
> The electrical tape is really not necessary on the outside at all,
> except for perhaps keeping dirt and dust from sticking to the sticky
> outer surface of the sealer tape.
> I suppose electrical tape offers some amount of protection, but its so
> minimal as to be useless.
> So, don't put electrical tape on first, then the sealer...who ever
told
> you this was not using his/her collective grey sells in a productive
> manner.
> However, any of the connections i put together, always have a good
chunk
> of sealer tape on them, as well as a wrap of electrical tape on the
> outside...better safe then sorry I always say.
> If the connection is going to be in a particularly wet location, such
as
> near the ground on a vehicle, or near the roof where water flows off,
> then use plenty of sealer tape, at least two complete layers to insure
> all wraps are over lapped.
> Also, you should wrap not only the point of connection, but also the
> spot where the coax enters the PL259connecter. If you make this all
one
> complete continuous wrap from the same peace of tape, then the seal
will
> be very good.
> You won't have any leakage problems as long as the ends of the tape or
> seal are well sealed.
> The tape backing is to keep the tape from sticking to itself on the
> roll, so always take that off...since its just paper, with the first
> rain, it will dissolve and cause large gaps in the tape and break the
> seal.
> good luck.
> I'd love to be able to outfit an RV with ham antennas...sounds like a
> fun project.
> 73
> Colin, V A6BKX
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.5.441 / Virus Database: 268.17.36/681 - Release Date:
2/11/2007
6:50 PM
>
>
|
