When I think about your problem, I don't think I or anyone else who doesn't own your model can tell you exactly what your settings should be... especially seeing as your system has a non default config, particularly with the addition of a zip drive. Depending on the age of your system, your CDROM drive might be running off of your sound card. Depending on the age and BIOS of your board it will ship either with a bunch of values set to the standard values, "default" or left on "auto". When you replaced that battery, you automatically got reset to default values. But, try the simplest and least painful things first. In the course of replacing the battery, you may have knocked a cable slightly loose even though it apears to be plugged in. Check that all cables are plugged in. If you unplugged one of the cables... particularly power and IDE data. Check them, particularly the orientation of the IDE data cable on all three of its connectors. Next, I would see if you have onboard ide channel 2 enabled in BIOS. I would also not edown what the pio/udma mode setings are for that channel. (Rarely, you have to set the pio mode manually rather than trusting auto settings.) However, if your second ide channel has been enabled all this time... life is going to get interesting The good news is that we can predict likely suspects to check. If you've had to proceed this far than it's likely something has knocked off the irq for your second IDE channel. Certain types of devices tend to go for certain resources. If for example, you have an internal modem, it would be in conflict with onboard com2 unless either automagically or manually, one of the two was set to com3 or com4. Com3/com4 take non standard interrupts, frequently irq5. If the com ports get there first... your sound card gets bumped off 5 (which sound cards tend to go for autmatically) and now goes looking for its own... bumping off something else. Network cards, I guess because they might get installed in a diskless work station, also contend for non standard interrupts like 5, 9, 10, 11, 12, 13, 14, 15 Thing is, if you have USB support, that probably is taking 10. If you have a ps/2 mouse, 12 is gone. If you have an two ide channels and a VGA card 13, 14 and 15 should _never_ be used. Particularly if you have all your cards in plug and play mode, a reset CMOS or an operating sytem re-install may emulate 52 card pickup, that is a lot of your resources get reshuffled. If you have a sound card or network card, it is likely involved. And I think the whole event may have been triggered by an extra com port (probably the second physical one on board) coming back to life as result of a default setting in CMOS. This may seem a little byzantine but I have seen this soooooooooo often. The good news, is that with a Micron system (quality!) you can reliably disable a serial port in BIOS and trust that it is disabled. However, it's a crap shoot with "quality challenged" systems like Packard Bell, AST or many generic motherboards. So, believe it or not: If the IDE channel has been enabled all this time, then I'd check for a com3 or com4 in Control Panel - System - Device Manager. Check for other ! and ? in there while you are at it. If you have com3/com4, investigate whether it is being used by an onboard serial port or an internal modem. I would try to end up with the internal modem on com2 and the second external com port disabled. If I still had the problem after a power off, power on. Go into one of the more advanced BIOS submenus and look for options like reset plug and play data or update ESCD. Save options and reboot with reset button or off/on. If that doesn't fix it, I'd physically remove the network and sound card (unless the CDROM is plugged into it), reboot and run the add hardware wizard. That was more than enough detail for now. Let the list know how things go and good luck! If this doesn't fix things, include the age of the BIOS and both make and model of any plug and play cards in your system. Matthew George Parmenter wrote: > Hi, > After noticing that my clock was steadily losing time I bought a new cmos > battery and replaced the old one. I thought I had written all the cmos > settings down. After rebooting and restoring all the settings I find that > my cdrom and my zip drive are not recognized anymore. How can I find what > the settings should be? Any help with this would be greatly appreciated. It > is a Phoenix version 4 release 6 bios on a Micron MME. The NOSPIN Group Promotions is now offering Mandrake Linux or Red Hat Linux CD sets along with our NOSPIN Power Linux CD... at a great price!!! http://freepctech.com/goodies/promotions.shtml