Kenneth:
You might want to give these instructions to "icanworkthisthing.com". Also,
Pat Tice at Handihams is building a section of the Handiham web site for
manuals, cheat sheets, and other such items.
Best 73 from Tom Behler: KB8TYJ
----- Original Message -----
From: "Kenneth Lee" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Friday, February 11, 2005 10:54 PM
Subject: TM-V7A quick ref
> Here are my v7 notes. Pardon my shorthand. When you see "1s" it means to
> press and hold the key for one second. If you're new to the v7 these notes
> probably wont make any sense. Let me know of any mistakes.
>
> 73, Ken --notes below
> Function keys are on front panel, between tuning dial and band selectors.
> Normal: F, TONE, reverse, LOW
> After pressing [F]: OFF, tone select, SHIFT, VISUAL
>
> [CALL] - recalls call memory
> [CALL1s] - Monitors call and memory or call and vfo
> [F][CALL] - Stores currently displayed frequency settings into call memory
>
> [VFO] - Recalls the VFO
> [VFO1s] - VFO or programmable band scan
> [VFO1s][MHZ] - Starts 1 kHz scan
> [PowerOn_VFO] - Partial reset, [VFO] to verify. memory channels are not
> erased
>
> [MEM] - Recalls most recently used memory, Boop on channel #1
> [MEM1s] - Memory scan
> [F][MEM] - Store current displayed frequency into current selected memory
> [F][MEM1s]frequency[MEM] - Store odd split
> [PowerOn-MEM] - Clear all memory, [MEM] to verify
> [MHZ] - 1 MHz tuning of VFO, MHz turns off
> [F+MHZ] - 10 MHZ tuning of VFO, [F] turns off
> [MHZ1s] - Enable AM mode, [MHZ] to toggle AM/FM
> [F][MHZ] - Key lock
> [PowerOn_MHZ] - All lock
> [PowerOn_MHZ] [MEM] - Erase currently selected memory
> Can not erase channel #1
>
> [TONE] - CTCSS Tone, press again to turn on tone squelch. Boop means no
> tone.
> [F1s][TONE] - Select tone frequency.
> You can use "Enter" and two digit CTCSS number (see CTCSS table)
> [TONE1s] - Search for CTCSS tone
> [F][TONE] - DTSS, again for DTSS squelch. Boop means no DTSS
> [F1s][REV] - set 3 digit DTSS code. You can use the Mic keypad.
> [REV] - Listen to repeater input
> [REV1s] - Auto simplex checker. [REV] cancels
> [F][REV] - Repeater shift +/-/simplex (boop = simplex)
>
> [LOW] - Power level, Boop = High
> [F1s][LOW] - Set frequency step size
> [PowerOn_LOW] - in memory mode only memory number is displayed
> [PM]# - Select 1 of 4 memories (one of the four function keys).
> [F][PM]# - Store 1 of the 4 PM memories.
> Auto PM store - Menu #4.4
> [PowerOn_CALL] - Clear PM memories [CALL] to verify
> [F][Menu] - Auto band select, PTT or band select to cancel
> [F][CONT] - Select VHF/VHF or UHF/UHF
> [F][BandSelect] - Disable the selected band
> [PowerOn_F] - Demo mode
>
> Commonly used menu options
> Scan resume mode - Menu #8 Time or carrier
> Advanced Intercept Point (AIP) - Menu #9, On or OFF (Off default)
> Auto Power Off (APO) - Menu #10, On or OFF (Off default)
> Time out Timer - Menu #11 (3, 5 or 10 min) 10 default
> Beep volume - Menu #14.1
>
> Re-assign PF keys on microphone by holding down one of the PF Keys during
> power up.
> Then press a front panel key to assign it to the mike PF key.
> Pressing the PTT assigns the PF key to toggle between VFO and MEM.
> Pressing VHF assigns the PF key to toggle between VHF and UHF.
> Microphone control - Menu #16.1
> Menu #16.2 thru #16.5 re-assigns mike pf keys.
> The PF options are user/ monitor/ enter/ voice/ and Power (for PF1 only).
>
> --
> No virus found in this outgoing message.
> Checked by AVG Anti-Virus.
> Version: 7.0.300 / Virus Database: 265.8.7 - Release Date: 2/10/2005
>
|
