Thanks, Ed.
I've been a fan of Diamond products for years, so will definitely check into
this!
73 from Tom Behler: KB8TYJ
----- Original Message -----
From: "Ed Malmgren" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Wednesday, March 09, 2011 11:55 AM
Subject: Re: splicing coax
Hi Tom. The trunk mount I had once was made by Diamond and it slides down
on the top lip of the trunk lid and is lined by rubber where it goes on the
outside. Some set screws tighten from the under side. cheers
Ed K7UC
----- Original Message -----
From: "tom behler" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Wednesday, March 09, 2011 9:01 AM
Subject: Re: splicing coax
> Thanks, John.
>
> I'll definitely check the trunk mount possibility out.
>
> What kind of trunk mount do you have? How did you insulate it from the
> trunk itself? I have to be careful because our vehicle is leased.
>
> 73 from Tom Behler: KB8TYJ
>
> ----- Original Message -----
> From: "John Miller" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Wednesday, March 09, 2011 10:58 AM
> Subject: Re: splicing coax
>
>
> that doesn't need the ground plain, I have the same antenna but with the
> uhf
> connector, mainly because that's what was in stock when I bought it but
> anyway, that doesn't need it. I ran mine on a trunk mount, insulated from
> the actual trunk of the car, and it didn't leave marks. It's not on the
> current car because the current one won't last long but the next car, I'm
> putting that back on.
> ----- Original Message -----
> From: "tom behler" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Wednesday, March 09, 2011 10:45 AM
> Subject: Re: splicing coax
>
>
>> John:
>>
>> The mobile antenna I use is an NMO type Diamond 770.
>>
>> I'll have to check the book to see what it says about needing a ground
>> plane
>> to work well.
>>
>> 73 from Tom Behler: KB8TYJ
>>
>> ----- Original Message -----
>> From: "John Miller" <[log in to unmask]>
>> To: <[log in to unmask]>
>> Sent: Wednesday, March 09, 2011 10:41 AM
>> Subject: Re: splicing coax
>>
>>
>> they make uhf and vhf antennas that don't need the grounding from the car
>> body, I have one and it works great, in fact I may have 2, I think the
>> one
>> in my go kit is that way as well. They're not all that cheap but they
>> sure
>> work.
>> ----- Original Message -----
>> From: "tom behler" <[log in to unmask]>
>> To: <[log in to unmask]>
>> Sent: Wednesday, March 09, 2011 9:57 AM
>> Subject: Re: splicing coax
>>
>>
>>> Michael:
>>>
>>> Can you give me the information on that N M O mount you describe?
>>>
>>> Might be a good possibility, although I wonder how well an antenna
>>> mounted
>>> so low on the car body would do, especially with the lack of a
>>> sufficient
>>> ground plane beneath it.
>>>
>>> 73 from Tom Behler: KB8TYJ
>>>
>>> ----- Original Message -----
>>> From: "Michael Thurman" <[log in to unmask]>
>>> To: "For blind ham radio operators" <[log in to unmask]>;
>>> "tom
>>> behler" <[log in to unmask]>
>>> Sent: Wednesday, March 09, 2011 9:52 AM
>>> Subject: Re: splicing coax
>>>
>>>
>>> they make a very very nice nmo mount that secures to the trunk with 4
>>> set
>>> screws that do not even drill into the body, the rest of the mount is
>>> rubber
>>> covered so it is invisible when removed from the car. also there are
>>> some
>>> good glass mount antennas, but they only work if you don't have tinted
>>> glass, and most cars have that unfortunately there is also another type
>>> of
>>> mount that goes behind the license plate where the plate mounts to the
>>> car.
>>> Those are good enough for een a hamstick antenna, or a big colinear 2m
>>> antennaand leave absolutely no marks on the car whatsoever
>
|
