Yes, I know PM means Program Memory or maybe partial memory, but
I am always hitting the button just below the power button so the
rig won't say PM or PM 1 or whatever. I once heard it say PM 5,
never figured out how it got to PM 5, or how I got it turned off,
Guess I'll have to read the manual, Jim WA6EKS
----- Original Message -----
From: Frank Ventura <[log in to unmask]
To: [log in to unmask]
Date sent: Fri, 31 Jul 2015 06:02:17 +0000
Subject: Re: TMV71A, question?
Hi Matt, sorry disregard my previous response. After I sent the
email I rea=
lized that you meant the reverse button next to the TX Power
button.
However, I have another question for anyone. On the TMV71a when
I power up=
or change receivers to the B receiver the last thing it says is
"PM Off" w=
hat does that mean?
Thanks
Frank
-----Original Message-----
From: For blind ham radio operators
[mailto:[log in to unmask]] =
On Behalf Of Matthew Chao
Sent: Thursday, July 30, 2015 6:51 AM
To: [log in to unmask]
Subject: Re: TMV71A, question?
No, need to find a different offset. You need to hit function
key,=20
followed by the plus/minus key. Each time you do this, you
toggle=20
between modes: plus, minus, and simplex. You'll know where you
are=20
because if you hit the offset key by itself, hit the A button
(for=20
example), and then repeat the process, you'll either hear a
frequency=20
change or not. In automatic, any repeater on 2 meters above 147
has=20
a plus offset; any repeater below 147 has a minus offset. Hope
this=20
helps.--Matt.
P.S. Get up on the HandiHam Web site. There's an audio demo of
this=20
by Steve Dresser.
At 10:18 AM 7/30/2015 +0000, you wrote:
Matt, interesting you ask this. Bob and Tony were here last
night and we w=
e=3D
re working with the TMV71a and had an issue on the B receiver.
We got the =
f=3D
req in correctly and I think the Pl as well but couldn't figure
out how to=
=3D
set it to a negative offset. Is that the same issue you have?
Frank
-----Original Message-----
From: For blind ham radio operators
[mailto:[log in to unmask]]=
=3D
On Behalf Of Matthew Chao
Sent: Wednesday, July 29, 2015 2:11 PM
To: [log in to unmask]
Subject: Re: BMV71A, question?
Yes, my bad. TMV71A. How do I change the repeater offset for
one of my c=
h=3D
annels? Thanks.--Matt, N1IBB.
At 09:54 AM 7/29/2015 -0700, you wrote:
Hi and thanks Doug. Will be running around today, not on the
air,=3D20
probably get on the swap net tomorrow evening. 73, Jim
----- Original Message -----
From: doug and sheilla emerson <[log in to unmask]
To: [log in to unmask]
Date sent: Wed, 29 Jul 2015 09:25:28 -0700
Subject: Re: BMV71A, question?
Jim, sorry I missed you yesterday on 147.195. I just checked out
my t =
=3D20
m v
71 A. Menu 100 allows you to set low and high scanning
peramaters. =3D2=
0
Menu 101 allows you to set frequency steps for your v f o.
With=3D20
reguard to Matt's question, I don't know how to set an odd
repeayter=3D2=
0
offset.
However, a few
weeks back, someone on the list posted that information. Perhaps
that=
=3D20
someone will do it again. hth. 73. Doug, N6NFF
-----Original Message-----
From: Jim Gammon
Sent: Tuesday, July 28, 2015 3:59 PM
To: [log in to unmask]
Subject: Re: BMV71A, question?
Doug, I'm curious, what do those menu selections do for the rig?
I am listening to 147.195 if you want to call me there, Jim
WA6EKS
----- Original Message -----
From: doug and sheilla emerson <[log in to unmask]
To: [log in to unmask]
Date sent: Tue, 28 Jul 2015 15:26:37 -0700
Subject: Re: BMV71A, question?
Curtis, in order for your t m v 71 A to see menus 100 and 101,
your=3D20
radio must be in the v f o mode, not the m r memory recall mode.
Push=
=3D20
the button in the uupper left hand corner of the radio. If you
hear=3D2=
0
the voice say v f o, you're good to go. You will then see menus
100=3D2=
0
and 101. h t h. Doug, N6NFF
-----Original Message-----
From: Curtis Delzer
Sent: Tuesday, July 28, 2015 1:54 PM
To: [log in to unmask]
Subject: BMV71A, question?
Hi all! I have the radio, but seems there is no menu 100 or 101.
One of
them is "programmable vfo" and the other is "step size."
Why are my two menus missing?
THANKS! I am creating a braille copy of the menu system with
comments=3D=
20
as to how to program memory channel names using the microphone,
all put=
=3D20
together in one place and it should be available soon!
-----
Curtis Delzer, HS.
K6VFO
San Bernardino, CA
|