Well, the full reset is probably your best shot, especially since you have
all your memories and menu settings backed up.
Steve
----- Original Message -----
From: "Curtis Delzer" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Monday, May 27, 2013 14:23
Subject: Re: tmv-71
> which should I reset, VFO, etc> hmm! thanks! you're probably right,
> and I do have the memories, etc. backed up on my computer.
>
> At 09:12 AM 05/27/13, you wrote:
>>I can't explain that one; I've heard that pause on every Kenwood I have
>>with
>>that feature. Granted, it's a very short pause, maybe a tenth of a
>>second,
>>but it's there on all my radios. May be time for a reset.
>>
>>Steve
>>
>>----- Original Message -----
>>From: "Curtis Delzer" <[log in to unmask]>
>>To: <[log in to unmask]>
>>Sent: Monday, May 27, 2013 03:36
>>Subject: Re: tmv-71
>>
>>
>> > that is the point, I am not hearing that "pause" or any audible of
>> > anything happening, only the high error beep when I hold the reverse
>> > button for longer than a second.
>> >
>> >
>> > At 09:35 AM 05/26/13, you wrote:
>> >>Curtis,
>> >>
>> >>The only audible thing you'll hear is a momentary pause while the radio
>> >>checks the input. I don't think you'll actually hear any audio present
>> >>on
>> >>the input (at least, I never have).
>> >>
>> >>Steve
>> >>
>> >>----- Original Message -----
>> >>From: "Curtis Delzer" <[log in to unmask]>
>> >>To: <[log in to unmask]>
>> >>Sent: Sunday, May 26, 2013 02:10
>> >>Subject: Re: tmv-71
>> >>
>> >>
>> >> > pressing "rev" is the "reverse key," which then=20
>> >> > monitors the input of the repeater. holding down=20
>> >> > the "rev" or reverse key is suppose to turn on=20
>> >> > the automatic frequency checker, and also then,=20
>> >> > every 3 seconds, the transceiver actually goes=20
>> >> > into the reverse mode automatically listening to=20
>> >> > the input of the repeater.. the icon blinking=20
>> >> > means it hears something on the input, but I just=20
>> >> > cannot get it to do something audibly, though I=20
>> >> > think I did hear it work, once. meaning it was=20
>> >> > turned on once, but I never got it to do it again. :)
>> >> >
>> >> >
>> >> > At 07:29 PM 05/25/13, you wrote:
>> >> >> The automatic frequency checker sounds like a visual thing.
>> >> >>
>> >> >> >From the manual
>> >> >>
>> >> >>Press [REV] (1s) to turn the ASC ON.
>> >> >>
>> >> >>When the ASC is ON, the icon will appear on the display.
>> >> >>
>> >> >>=B7 While direct contact is possible, without the use of a repeater,
>> >> >>the=
>> >> > icon
>> >> >>will
>> >> >>
>> >> >>begin blinking.
>> >> >>
>> >> >>=B7 To exit ASC, press [REV].
>> >> >>
>> >> >>Note:
>> >> >>
>> >> >>Pressing [PTT] will cause the icon to stop blinking.
>> >> >>
>> >> >>ASC does not function if you are using simplex operation.
>> >> >>
>> >> >>ASC does not function while scanning.
>> >> >>
>> >> >>Activating ASC while using Reverse will switch the Reverse function
>> >> >>OFF.
>> >> >>
>> >> >>If you recall a Memory channel or the Call channel, and those
>> >> >>channels
>> >> >>are
>> >> >>set
>> >> >>
>> >> >>up with the
>> >> >>
>> >> >>Reverse function switched ON, the ASC will switch OFF.
>> >> >>
>> >> >>A
>> >> >>
>> >> >>
>> >> >>
>> >> >>
>> >> >>
>> >> >>display and blinks. Press any key other than the Tuning control
>> >> >>while
>> >> >>the
>> >> >>
>> >> >>I wonder what "press "rev" means, I think they are talking about
>> >> >>menu=
>> >> > setup,
>> >> >>but am not sure about the manual's translation, or my understanding.
>> >> >
>> >
>
|
