Maybe the volume control is at the input to the speech board.  That would 
explain why it is in different places on different radios.

Steve

----- Original Message ----- 
From: "Russ Kiehne" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Friday, March 19, 2010 09:28
Subject: Re: ic-718


> That seems to be the case.  I would have thought the adjustment would have
> been on the board itself.
>
> ----- Original Message ----- 
> From: "Butch Bussen" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Thursday, March 18, 2010 12:19 PM
> Subject: Re: ic-718
>
>
>> Yes, but the instructions don't say the resister is on the synthesizer
>> board, it just says r75 which I'd guess is somewhere else in the
>> receiver.  Just as icom tole me to adjust r2701, which certainly isn't
>> on the ut102.  If the adjustment was actually on the board itself, one
>> wouldn't think a special note had to be sent to tell a person where  to
>> adjust the level.
>> 73
>> Butch Bussen
>> wa0vjr
>> open Node 3148
>> Las Vegas
>>
>>
>> On Thu, 18 Mar 2010, Colin McDonald wrote:
>>
>>> but the r75 uses the UT102 synthesiser doesn't it?
>>> an ut102 is the same board in any radio, and if there are instructions 
>>> to
>>> adjust volume with a VR on the UT102 for the r75, those same 
>>> instructions
>>> would hold true on the ic718 using an UT102 no?
>>> seems like there is a bit of conflicting information here...icom and the
>>> AES
>>> tech say no VR adjustment on the board, where others, non official techs
>>> say
>>> there is...wonder which it is.
>>> 73
>>> Colin, V A6BKX
>>> ----- Original Message -----
>>> From: "Steve Dresser" <[log in to unmask]>
>>> To: <[log in to unmask]>
>>> Sent: Thursday, March 18, 2010 9:00 AM
>>> Subject: Re: ic-718
>>>
>>>
>>>> Russ,
>>>>
>>>> I think the instructions you posted were for the R75, not the 718.
>>>>
>>>> Steve
>>>>
>>>> ----- Original Message -----
>>>> From: "Russ Kiehne" <[log in to unmask]>
>>>> To: <[log in to unmask]>
>>>> Sent: Thursday, March 18, 2010 09:29
>>>> Subject: Re: ic-718
>>>>
>>>>
>>>>> Did you see the followup I posted on this?  If not, I'll post it 
>>>>> again.
>>>>> ----- Original Message -----
>>>>> From: "Butch Bussen" <[log in to unmask]>
>>>>> To: <[log in to unmask]>
>>>>> Sent: Wednesday, March 17, 2010 11:08 AM
>>>>> Subject: Re: ic-718
>>>>>
>>>>>
>>>>>> Are you sure? I spoke with icom and a e s and both tell me there is 
>>>>>> no
>>>>>> adjustment on the board.  I'm confused, and the speach board is
>>>>>> mounted
>>>>>> under the add on digital noise reduction module, so not easy to get 
>>>>>> at
>>>>>> unless I'm sure.
>>>>>> 73
>>>>>> Butch Bussen
>>>>>> wa0vjr
>>>>>> open Node 3148
>>>>>> Las Vegas
>>>>>>
>>>>>>
>>>>>> On Wed, 17 Mar 2010, Russ Kiehne wrote:
>>>>>>
>>>>>>> The adjustment is on the speech board itself.
>>>>>>> ----- Original Message -----
>>>>>>> From: "tom behler" <[log in to unmask]>
>>>>>>> To: <[log in to unmask]>
>>>>>>> Sent: Tuesday, March 16, 2010 5:55 PM
>>>>>>> Subject: Re: ic-718
>>>>>>>
>>>>>>>
>>>>>>>>    Butch:
>>>>>>>>
>>>>>>>> I swear there is an adjustment in one of the menus for UT102 
>>>>>>>> volume.
>>>>>>>>
>>>>>>>> I seem to recall having that problem with mine too, but remember
>>>>>>>> adjusting
>>>>>>>> it.  I had to, because it was a rig that I used for Field Day, and
>>>>>>>> often
>>>>>>>> in
>>>>>>>> our motor home, so needed the volume to be a bit higher than usual.
>>>>>>>>
>>>>>>>> 73 from Tom Behler:  KB8TYJ
>>>>>>>>
>>>>>>>> ----- Original Message -----
>>>>>>>> From: "Butch Bussen" <[log in to unmask]>
>>>>>>>> To: <[log in to unmask]>
>>>>>>>> Sent: Tuesday, March 16, 2010 5:54 PM
>>>>>>>> Subject: Re: ic-718
>>>>>>>>
>>>>>>>>
>>>>>>>> I did go to a e s and bought the synthesizer and the i-100 tuner. 
>>>>>>>> I
>>>>>>>> considred getting the at-100, but they didn't have one in stock and
>>>>>>>> I
>>>>>>>> wasn't sure what the up down manual tuning buttons did and all 
>>>>>>>> that,
>>>>>>>> so
>>>>>>>> I
>>>>>>>> figured I'd keep it simple, just one button.  On another note, the
>>>>>>>> synthesizer works, but the level seems low.  It is fine if you 
>>>>>>>> don't
>>>>>>>> have
>>>>>>>> much signal, but it is covered up by the noise unless I turn the rf
>>>>>>>> gain
>>>>>>>> down.  Any suggestions?  I called a e s and they said no level
>>>>>>>> adjust
>>>>>>>> on
>>>>>>>> the board.  I called icom and they are supposed to call me back.
>>>>>>>>
>>>>>>>> Yep, it is a nice little radio, nice for portable or mobile, just a
>>>>>>>> simple
>>>>>>>> little rig.
>>>>>>>> 73
>>>>>>>> Butch Bussen
>>>>>>>> wa0vjr
>>>>>>>> open Node 3148
>>>>>>>> Las Vegas
>>>>>>>
>>>>>>>
>>>>>
>>>
>>>
>