Hi David and all,
Thanks for this reply and I apologize for the delay in answering. There
was a family emergency here and I have been away for awhile.
I configured the network as you recommended below, i.e., one computer
has an IP address of 192.168.2.1 and the other has 192.168.2.2. I can
"ping" 192.168.2.2 from 192.168.2.1 and get the following reply and get
a round trip time of average = 815ms. I CANNOT "ping" 192.168.2.1 from
192.168.2.2 -- the "ping" request just times out.
I want to be able to share files and printers on this network. The
printers are all connected to the 192.168.2.1 computer.
BTW, the WinXP Pro computer, 192.168.2.1, has a NVIDIA nForce Networking
Controller. The WinXP Home computer, 192.168.2.2, has a 3Com Etherlink
XL 10/100 PCI. When I enabled the network on 192.168.2.1 I got a notice
that it was connected at 100mb.
Thanks for the help...again, I apologize for the late reply.
Loy
David Gillett wrote:
> On 26 Jul 2007 at 13:30, Loy Pressley wrote:
>
>
>> I want to connect two computer for file and printer sharing. There is
>> an Ethernet connection on both computers. I bought a crossover cable
>> with RJ45 connectors on each end and connected the two computer using
>> the cable. When I made the connection, one of the computers began
>> flashing that a network cable was disconnected. I ran the network setup
>> wizard and told it to ignore the disconnected cable. It doesn't flash
>> any more but neither do the two computers appear to be able to see each
>> other.
>>
>> I am a complete buffoon at this. All I want to do in connect two
>> WinXPSP2 computers. One has WinXP Pro and the other WinXP Home.
>> According to everything I could find, all I needed was the right
>> crossover cable and I was ready to go. I ordered the cable and hooked
>> the two computers together and no joy. For this simple network I think
>> I have all the hardware I need. I certainly do need some help setting
>> it up, though. Any help would be greatly appreciated.
>>
>
> Although it is possible to use a crossover cable to make a point-to-point
> connection like this, Ethernet is designed to use a hub or switch to
> interconnect multiple host machines. So each machine will need an IP
> address configured for its Ethernet adapter. These addresses need to be
> distinct, but within the same address range.
>
> The default configuration is going to say "Obtain address automatically",
> but this requires that some machine, with an address configured, be set up
> to hand out addresses to other machines. If you enable ICS (Internet
> Connection Sharing) on one of the machines, it can do that, but that may
> require that t also HAVE a separate Internet connection.
>
> A simpler approach is to assign each machine an address in a common
> private range. If you go through the Network config to the properties of
> the Ethernet connector, and look at TCP/IP proertires, you'll see three
> boxes -- address, subnet mask, and default gateway.
>
> All addresses that start with "192.168." are private, and are intended to
> be used with a mask of "255.255.255.0". Many retail network procts such as
> routers come preconfigured to use the 192.168.0.x or 192.168.1.x ranges, so
> let's use 192.168.2.x, where x is 1 on one machine and 2 on the other.
>
> The default gateway is the address of a devide that connects this private
> network to other address groups, including the whole internet. Since you're
> not connecting it, you can leave that blank.
>
> Once that is set one each PC, they should be able to see each other. From
> the one that is 192,168,2,1, open a command prompt and type "ping
> 192.168.2.2". You should get four responses showing a very brief time for a
> packet to reach the other machine and a response to be received.
>
> David Gillett
>
> The NOSPIN Group has added a new feature on our website,
> web based bulletinboard for questions and answers:
> Visit our sister website at http://nospin.com
>
>
The NOSPIN Group is now offering Free PC Tech
support at our newest website:
http://freepctech.com
|