Yes they do have up/down buttons. They do not have PF keys, which is too
bad because I'd like to define some of them as I would on a hand mic.
Steve
----- Original Message -----
From: "Brett Winches" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Monday, May 14, 2007 18:16
Subject: Re: Mc60 mc80 mc85 ...was...RE: changing mike gain on tmv7a
> Do all three have up down frequency or memory control?=20
>
>
>
> -----
> BRETT WINCHESTER
> [log in to unmask]
> 208-639-8386
> ###
>
>
> -----Original Message-----
> From: For blind ham radio operators
> [mailto:[log in to unmask]] On Behalf Of Steve Dresser
> Sent: Monday, May 14, 2007 3:38 PM
> To: [log in to unmask]
> Subject: Re: Mc60 mc80 mc85 ...was...RE: changing mike gain on tmv7a
>
> Brett,
>
> All three are desk mics designed to work with Kenwood radios. The
> MC-60A is the only one currently available from stores. Check for
> prices at your favorite store. It has a high/low impedance switch, and
> I think it has a preamp although I'm not sure. The MC-80 doesn't have a
> high/low switch, but it does have a preamp and an adjustable gain
> control on the back of the base. The MC-85 can run two or three radios
> off its multiple outputs. I've never seen this one, but I've heard it's
> good. It may have an equalizer, but I'm not sure.
>
> Steve
>
> ----- Original Message -----
> From: "Brett Winches" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Monday, May 14, 2007 14:44
> Subject: Mc60 mc80 mc85 ...was...RE: changing mike gain on tmv7a
>
>
>> Steve, Can you please refresh me as to what mic is what for these?
>> =3D20
>>
>>
>>
>> -----
>> BRETT WINCHESTER
>> [log in to unmask]
>> 208-639-8386
>> ###
>>
>>
>> -----Original Message-----
>> From: For blind ham radio operators
>> [mailto:[log in to unmask]] On Behalf Of Steve Dresser
>> Sent: Monday, May 14, 2007 12:03 PM
>> To: [log in to unmask]
>> Subject: Re: changing mike gain on tmv7a
>>
>> Tom,
>>
>> The MC-60A will work. So will an MC-80 (which is what I use), or an
>> MC-85.=3D20
>> In the case of the latter two mics, you'll have to buy them used.
>> You'll also have to get an adaptor to go from the Kenwood 8-pin
>> connector to an RJ45, but those adaptors are readily available from
> any
>> good ham radio store.
>>
>> Steve
>>
>> ----- Original Message -----
>> From: "T Behler" <[log in to unmask]>
>> To: <[log in to unmask]>
>> Sent: Monday, May 14, 2007 11:52
>> Subject: Re: changing mike gain on tmv7a
>>
>>
>>> Steve:
>>>
>>> That desk mic idea actually sounds like a possibility. ... I have
>> three
>>> TMV7A's and had actually thought of swapping one of the others out,
>> and
>>> putting it into the RV for our trip.
>>>
>>> I know the others don't have this problem.
>>>
>>> Then, I could just pick up a desk mic somewhere and use it with the
>> hot=3D20
>>> one
>>> at home as the base unit.
>>>
>>> Any recommendations on a desk mic that would fit the TMV7A?
>>>
>>> 73 from Tom Behler: KB8TYJ
>>>
>>> ----- Original Message -----=3D20
>>> From: "Steve Dresser" <[log in to unmask]>
>>> To: <[log in to unmask]>
>>> Sent: Monday, May 14, 2007 11:15 AM
>>> Subject: Re: changing mike gain on tmv7a
>>>
>>>
>>>> Tom,
>>>>
>>>> If you use a desk mic with a gain control, you don't even need to
>> worry
>>>> about whether there's a gain control on the radio. Alternatively,
>> you
>>>> might
>>>> be able to get someone to build you a box with a 10000 Ohm pot to do
>> the
>>>> job. I know these aren't good solutions for using the radio in a
>> mobile
>>>> environment, but they would work nicely for a base rig.
>>>>
>>>> Steve
>>>>
>>>> ----- Original Message -----=3D20
>>>> From: "T Behler" <[log in to unmask]>
>>>> To: <[log in to unmask]>
>>>> Sent: Monday, May 14, 2007 08:24
>>>> Subject: Re: changing mike gain on tmv7a
>>>>
>>>>
>>>>> Colin and all.
>>>>>
>>>>> Well, this is interesting, and I'll let you guys know what the
>> Kenwood
>>>>> tech
>>>>> says in response to my inquiry.
>>>>>
>>>>> What Colin is saying makes sense, but at the same time, I find it
>>>>> interesting that a company would make a radio that you can't
> control
>> the
>>>>> mic
>>>>> gain on.
>>>>>
>>>>> Although, come to think of it, HT's are that way--what you hear is
>> what
>>>>> you
>>>>> get.
>>>>>
>>>>> Anyway, will keep everyone posted.
>>>>>
>>>>> 73 from Tom Behler: KB8TYJ
>>>>>
>>>>> ----- Original Message -----=3D20
>>>>> From: "Colin McDonald" <[log in to unmask]>
>>>>> To: <[log in to unmask]>
>>>>> Sent: Monday, May 14, 2007 6:13 AM
>>>>> Subject: changing mike gain on tmv7a
>>>>>
>>>>>
>>>>>>I would beg to differ regarding an internal pot for the mike gain
> on
>> the
>>>>>>tmv7a.
>>>>>> If there are any internal pots at all, they control other
>> functions.
>>>>>> The
>>>>>> audio
>>>>>> gain, both receive and transmit are both controlled by the micro
>>>>>> processor
>>>>>> and
>>>>>> not controlled by an analog device. For instance when you use the
>>>>>> microphone
>>>>>> remote control feature, and use the volume and squelch adjustment
>>>>>> buttons,
>>>>>> the
>>>>>> radio adjusts those functions, and as soon as you go to adjust
> them
>>>>>> again
>>>>>> on
>>>>>> the radio, it will default back to what ever it was before you
>> started
>>>>>> adjusting from the microphone. If there was an internal pot that
>>>>>> controlled
>>>>>> either audio or squelch, this could not be accomplished the way it
>> is.
>>>>>> The
>>>>>> same holds true for the tx audio. Since there is an option within
>> the
>>>>>> service
>>>>>> menu to adjust the tx audio, it wouldn't then also have an
> internal
>> pot
>>>>>> to
>>>>>> adjust since the internal processor is already controlling =
> that=3D20
>>>>>> function
>>>>>> nicely.
>>>>>> There are likely surface mount components that could be altered to
>>>>>> adjust
>>>>>> the
>>>>>> gain, in other words, the various information being sent to the
>>>>>> processor.
>>>>>> 73
>>>>>> Colin, V A6BKX
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>
>>>
>>>
>>>
>>
>>
>>
>
>
>
|
