Hi.
General coverage from 500 Khz to 35 MHz.
73, de Lou K2LKK
At 06:17 PM 9/2/2005 -0100, you wrote:
>Thanks Lou, one more question, is it general coverage or hambands only?
>Thanks, dd
>----- Original Message -----
>From: "Louis Kim Kline" <[log in to unmask]>
>To: <[log in to unmask]>
>Sent: Friday, September 02, 2005 9:13 PM
>Subject: Re: Will Kenwood TS140S Work With VS1 or vs2?
>
>
> > Hi.
> >
> > The display is digital and reads out to 10 Hz. It is a synthesized rig,
> > just no keypad or capability for a speech board. It was Kenwood's bottom
> > of the line radio when it was made.
> >
> > 73, de Lou K2LKK
> >
> > At 07:12 AM 9/2/2005 -0100, you wrote:
> > >Hi Lou, from their literature, it would seem that the Simplest way to use
> > >the freq mite is to capacitance couple/wrap a wire around the coax, or
> > >atatch it to the ground side of the coax plug to take transmitted signal
>and
> > >"count it."
> > >If the display on a rig is digital, that's a possibility alsok, though
>like
> > >you, I'd have to find someone else to do the "poking, hi hi. Thanks,
> > >Danny.----- Original Message -----
> > >From: "Louis Kim Kline" <[log in to unmask]>
> > >To: <[log in to unmask]>
> > >Sent: Friday, September 02, 2005 1:22 AM
> > >Subject: Re: Will Kenwood TS140S Work With VS1 or vs2?
> > >
> > >
> > > > Hi.
> > > >
> > > > You are a bit more adventurous than I when it comes to probing around
> > > > inside radios. I wouldn't have the foggiest idea where to pick up the
> > > > signal for the frequency mite in the Kenwood TS140S.
> > > >
> > > > Have fun.
> > > >
> > > > 73, de Lou K2LKK
> > > >
> > > > At 08:32 PM 8/31/2005 -0100, you wrote:
> > > > >Thanks LKK, I just wondered as I'm looking for an older simpler yet
> > > > >accessible and small as possible hf unit for a project, speech and
>keypad
> > > > >would be nice but not necessary cause I have the freqmite for this
> > >project.
> > > > >Open to suggestions, Danny.
> > > > >----- Original Message -----
> > > > >From: "Louis Kim Kline" <[log in to unmask]>
> > > > >To: <[log in to unmask]>
> > > > >Sent: Wednesday, August 31, 2005 10:24 PM
> > > > >Subject: Re: Will Kenwood TS140S Work With VS1 or vs2?
> > > > >
> > > > >
> > > > > > No.
> > > > > >
> > > > > > The Kenwood TS140S has no capabilities for speech output, keypad
> > >entry, or
> > > > > > an internal auto tuner. It's a pretty poor choice for a radio for
> > >someone
> > > > > > who is blind.
> > > > > >
> > > > > > 73, de Lou K2LKK
> > > > > >
> > > > > > At 04:41 PM 8/31/2005 -0100, you wrote:
> > > > > > >Hi All, wondering if any of you know if the Kenwood TS140 and
>140S
> > >radios
> > > > > > >will support either a vs1 or vs2 module, and if any of you either
> > >have
> > > > > > >experience with or one of that model hf radio you'd like to
> > >sell/swap.
> > > > > > >Thanks, Danny Dyer, wb4idu.
> > > > > >
> > > > > > Louis Kim Kline
> > > > > > A.R.S. K2LKK
> > > > > > Home e-mail: [log in to unmask]
> > > > > > Work e-mail: [log in to unmask]
> > > > > > Work Telephone: (585) 697-5753
> > > >
> > > > Louis Kim Kline
> > > > A.R.S. K2LKK
> > > > Home e-mail: [log in to unmask]
> > > > Work e-mail: [log in to unmask]
> > > > Work Telephone: (585) 697-5753
> >
> > Louis Kim Kline
> > A.R.S. K2LKK
> > Home e-mail: [log in to unmask]
> > Work e-mail: [log in to unmask]
> > Work Telephone: (585) 697-5753
Louis Kim Kline
A.R.S. K2LKK
Home e-mail: [log in to unmask]
Work e-mail: [log in to unmask]
Work Telephone: (585) 697-5753
|