ok i checked it for you.
It is section #14.1 in the manual
Go to menu number 11, TOT and press the set button, which, in the menu mode
is the Reverse button, the second one over from the right in the group of
four buttons...immediately beside your RF power selecter button.
Anyway, this button is the set button and you can toggle from 3, 5 and 10
minute time out defaults. There is probably an off setting there as
well....are you running cross band or using the rig for echolink or IRLP
that you need more then ten minutes of TX time?
73
Colin, V A6BKX
----- Original Message -----
From: "Colin McDonald" <[log in to unmask]>
To: <[log in to unmask]>
Sent: Friday, September 16, 2005 10:30 PM
Subject: Re: tmv7a question
> check out the tm V7A manual at
> www.icanworkthisthing.com
> under the amateur radio link, and then dual band transceivers, and then TM
> V7A manual.
> Look under section 14 and find the Time out Timer on off procedures.
> Its a menu item so you may or may not need sited assistance...depends on
if
> you remember the last menu you were in.
> Another way is just do a partial reset, turn radio off, hold down VFO and
> turn the radio on, then hit the vfo button again to complete.
> This will reset all menu defaults but will not erase memory.
> Remember, if you do a partial reset, the mike buttons wont work until you
> turn microphone on in menu 16 again.
> All directions for this are in the manual or i have created a
comprehensive
> cheat sheet to do it as well. Doing a partial reset will turn the time out
> timer off and set you back to menu 1 so you can count clicks to the
> appropriate menus that you want
> If you have big difficulties just call me on skype my screen name is
> greatcanadian
> 73
> Colin, V A6BKX
> ----- Original Message -----
> From: "Kevin Kwan" <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Friday, September 16, 2005 8:03 PM
> Subject: tmv7a question
>
>
> > This is a multi-part message in MIME format.
> >
> > ------=_NextPart_000_007D_01C5BB0A.6B655FC0
> > Content-Type: text/plain;
> > charset="iso-8859-1"
> > Content-Transfer-Encoding: quoted-printable
> >
> > Not that this is necessary but is there a way to disable the tot on this
=
> > rig, thanks?
> > ------=_NextPart_000_007D_01C5BB0A.6B655FC0
> > Content-Type: text/html;
> > charset="iso-8859-1"
> > Content-Transfer-Encoding: quoted-printable
> >
> > <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
> > <HTML><HEAD>
> > <META http-equiv=3DContent-Type content=3D"text/html; =
> > charset=3Diso-8859-1">
> > <META content=3D"MSHTML 6.00.2800.1400" name=3DGENERATOR>
> > <STYLE></STYLE>
> > </HEAD>
> > <BODY bgColor=3D#ffffff>
> > <DIV><FONT face=3DArial size=3D2>Not that this is necessary but is there
=
> > a way to=20
> > disable the tot on this rig, thanks?</FONT></DIV></BODY></HTML>
> >
> > ------=_NextPart_000_007D_01C5BB0A.6B655FC0--
> >
>
|
