Guys, now *this* sounds like fun!
I'm gonna buy one of these instead of a new HT--when, that is, I actually have some expendable cash.
----- Forwarded message from Eric Swartz WA6HHQ - Elecraft <[log in to unmask]> -----
To: Elecraft List <[log in to unmask]>, QRP-L <[log in to unmask]>,
GQRP <[log in to unmask]>
The Elecraft KX1 is a very compact, multi-band CW transceiver optimized for
backpacking and travel use. With internal battery, internal automatic
antenna tuner, plug-in keyer paddle, and log-book lamp, it offers a high
level of integration. The enclosure measures just 1.2 x 3 x 5.3 inches (3 x
7.5 x 13 cm), and the transceiver weighs just 9 ounces (11 ounces with both
the optional ATU and keyer paddle installed).
Unlike most transceivers, the KX1?s controls are located on the top of the
cabinet, and the keyer paddle attaches at the front. This ?trail-friendly?
format is ideal for hand-held or lap-top operation, e.g. when sitting on the
ground, using a camp chair, reclining, or even standing. The KX1 is also at
home on a table, providing an optimal viewing angle without a tilt stand.
The unique plug-in keyer paddle is angled at 45 degrees for ease of use and
is both physically and electrically reversible for right- or left-handed
operators.
The transceiver covers the full 40 and 20 meter bands, and optionally 30
meters. The VFO uses a DDS (direct digital synthesis) IC, so it can also
tune nearby SWL band segments. A variable-bandwidth crystal filter permits
reception of SSB and AM as well as CW. This facilitates cross-mode contacts
and reception of HF AM broadcast stations.
The KX1?s internal six-cell battery pack can be changed in seconds with the
removal of two thumb screws. The battery provides 1 to 2 watts power output.
An external 12 V supply increases output to about 4 watts. Low receive-mode
current drain (34 mA typ.) results in internal battery life of 20 hours or
more during casual operation.
The KX1 uses a highly-efficient 3-digit LED display that adds just 1 to 2 mA
to total current drain in moderate lighting conditions. The operator can
adjust both the display brightness and off-timeout (after last keypress).
Operation without the display is possible if the CW feedback feature is
turned on. This provides audible readout of the VFO frequency and other
information.
Additional features include frequency memories, three VFO tuning rates, RIT,
and S-meter display. The built-in keyer offers Iambic modes A and B and two
message buffers. In an emergency, two front panel switches can be used as a
keyer paddle or manual key.
The KX1 is suitable for first-time builders. The basic unit consists of a
single printed circuit board, with no surface mount components to install
(the three surface mount parts used are pre-installed).
The KX1 kit sells for $289. First shipments will commence at at the
Pacificon convention, Oct. 17-19th, and the week following.
For more information on the KX1, including pictures, data sheet and on line
ordering see the KX1 page at: http://www.elecraft.com
_______________________________________________
Elecraft mailing list: [log in to unmask]
You must be subscribed to post to the list.
To subscribe or unsubscribe see:
http://mailman.qth.net/mailman/listinfo/elecraft
Elecraft Web Page: http://www.elecraft.com
Also see: http://www.elecraft.com/elecraft_list_guidelines.htm
----- End forwarded message -----
--
Buddy Brannan, KB5ELV/3 | But I will lay my burden
Email: [log in to unmask] | in the cradle of your grace,
ICQ: 36621210 | And the shining beaches of your love,
http://www.ycardz.com | and the sea of your embrace.--Dave Carter
|
