Okay, this eliminates the hub/wiring as the culprit.

> We were able to access the web cam from within the local network,
> but not from outside.

  I'd say the address settings on the camera are the next things to
check.  Local access but not remote sounds like it's either (a) not
trying the right gateway, or (b) not trying the gateway when it in
fact should.
  You say this is a Novell network?  Is it using IP, or IPX, for
addressing?  If IP, check the gateway address and subnet mask, an
error in either could cause this kind of result.  IPX addressing
works differently, and it's not obvious (to me) how it could break in
this fashion -- maybe someone with more IPX familiarity knows.

David Gillett


On 5 Aug 2001, at 16:49, Ron Jobe wrote:

> The hub is a Netsurf 8-port, 10 Mb, Ethernet hub, model NC-N8PHub-R.  I
> picked it up from a clearance sale, new in the box.  It has 9 RJ-45 ports
> and 1 BNC.  Uplinks may be made via RJ-45 or BNC.  There is no switch for
> the uplink.  RJ-45 Port 1 is marked for uplink and is "tied" to Port 2
> (straight connection), so that only one may be active at a time.  When the
> uplink port (Port 1) is in use, and Port 2 open, the indicator lights show
> that both Ports 1 & 2 are in use.  Connections made were:
> Port 1 - Uplink
> Port 3 - Computer (later swapped to Port 5 for diagnostic testing).
> Port 4 - Web cam
> We were able to access the web cam from within the local network, but not
> from outside.  That was the goal - to share images with other conference
> sites.  However, we may have been using an incorrect IP address for the
> camera.  We'll discuss the IP address with the system administrator.
>
> Thanks!
> Ron Jobe
>
> ----- Original Message -----
> From: <[log in to unmask]>
> To: <[log in to unmask]>
> Sent: Sunday, August 05, 2001 1:40 PM
> Subject: Re: [PCBUILD] How does a additional hub affect a Novell network?
>
>
> > On 3 Aug 2001, at 18:20, Computers a la Carte wrote:
> >
> > > There is only 1 Ethernet line running into the worship center, so
> > > I disconnected that line from the computer and installed a small
> > > hub.  The hub's up-link port was connected to the incoming line.
> > > The computer and web cam were then connected to the hub.  The
> > > lights on the hub indicate the uplink, computer and web cam are
> > > working.  Have I done anything wrong to this point?
> >
> >   Whether this can work can depend on what's on the other end of that
> > single Ethernet line.  It could, for instance, be a bridge/switch
> > that only allows for a single device.
> >
> >   I've seen four variations of uplink ports on hubs.  It might be
> > helpful to know what model you have, so we know which situation
> > applies:
> >
> --- snip ---
> > 2.  Uplink port is apparently one of 5/9/17/25.  It is *actually* one
> > of 4/8/16/24, but this one port has two connectors, one wired for
> > regular use and one wired crossover for uplink use.  Uplink will not
> > function correctly if a devide is plugged into the regular-wired
> > connector for this port.
> --- snip ---
>
>          PCBUILD maintains hundreds of useful files for download
>                      visit our download web page at:
>                   http://freepctech.com/downloads.shtml
>

                         PCBUILD's List Owners:
                      Bob Wright<[log in to unmask]>
                       Drew Dunn<[log in to unmask]>